PDA

View Full Version : 96 caravan trans in limp mode ?


87poopcoupe
10-10-2008, 10:50 PM
my beater's tranny is in limp mode.. i can figure out what the dam codes are telling me though..

96 chrysler town & Country , 3.8, auto , air.. stupid 4 speed

trans code on snap mt2500 scanner is 36 , and 53

car is only running in like 1-2 gear... anyone ever had one do this before ?
or know what the problem may be

i was driving slowly in traffic, went to take back off after sitting still for 10 minutes and it started shifting all stupid.

checked the tranny fluid its still red (ATF+3 , and full )
Goober
10-10-2008, 10:56 PM
Does the speedometer act stupid too?
8banger
10-10-2008, 11:20 PM
36 =is fault immediatley after a shift.....which is accociated with code=
53=Speed Error gear ratio in 3rd.== possible cause internal transmission problem.


There is a TSB for these codes that may or may not fix your problem....
INPUT SPEED SENSOR...replace this,,fairly cheap to replace and have replaced several...

part no. 4412878 from the dealer..in order to properly diagnos,,a scanner is a must...need to see in input rpm is dropping out...could also be major trans issues..."clutch slippage"
87poopcoupe
10-10-2008, 11:30 PM
speedo works fine.... kinda odd to have major damage creepin along on interstate
8banger
10-10-2008, 11:34 PM
Kinda why I'd replace the input speed sensor first.. :D .....
Technical Service Bulletin No. 21-10-95
Mista Bone
10-10-2008, 11:51 PM
two shaft speed sensors, known to fail, about $19 each, easy to get to.
87poopcoupe
10-11-2008, 01:51 AM
well i got the scanner out and scanned it again... same codes.. i will change the fluid in the morn and test it again after quick relearn procedure.....

then i may need the sensors.... anyone seen this before on there car or a customers ?
87poopcoupe
10-11-2008, 03:41 AM
ok update 3 am.... took van down the road with scanner hooked up...

35mph input rpm was reading at 2400rpm , output was reading at 1500 rpm ? is that normal ?
87poopcoupe
10-11-2008, 03:42 AM
i am going to change the fluid and change input sensor in the morning.. not real sure if i should replace the output also.... time to sleep on it
8banger
10-11-2008, 10:33 AM
well i got the scanner out and scanned it again... same codes.. i will change the fluid in the morn and test it again after quick relearn procedure.....

then i may need the sensors.... anyone seen this before on there car or a customers ?


yes seveal times...majority of the time it was the input or outout sensor...

sure couldnt hurt to change both as both are common problems
87poopcoupe
10-11-2008, 11:23 AM
stupid question which sensor is input ?
Mista Bone
10-11-2008, 12:21 PM
BOTH sensors, do it!

$40 for two sensors or a $2700 for a rebuild.
87poopcoupe
10-11-2008, 01:11 PM
stopped by koi in mt carmel they said they only had a listing for 1 sensor
( input ).... trying to locate web pic of input sensor right now
87poopcoupe
10-11-2008, 03:17 PM
update.... change both speed sensors on tranny ... still shifting like crap , once it gets into 3rd gear it goes to limp mode.

on the snap on mt2500 scanner i have it has a quick learn feature , i tried that after clearing codes and disconnecting battery.still no 3rd gear

also did the quicktests through scanner and it tested all tranny solenoids, all tested fine