Flaming87lx
09-15-2010, 04:10 PM
http://i249.photobucket.com/albums/gg237/mustang398/carb.jpg
http://i249.photobucket.com/albums/gg237/mustang398/3603.jpg
http://i249.photobucket.com/albums/gg237/mustang398/3602.jpg
http://i249.photobucket.com/albums/gg237/mustang398/89droid3.jpg
http://i249.photobucket.com/albums/gg237/mustang398/89droid2.jpg
http://i249.photobucket.com/albums/gg237/mustang398/89hatch5.jpg
*******Roller*******
Solid car, no rust, solid floor pans, solid strut towers. Nice paint, front and rear bumpers need some touch up, and minor damage to bottom of lf fender (behind the tire) Heater box is out but wipers and lights all still work. They sell 12v heaters on ebay that are very reasonable if you want heat back in the car. Has 8.8 w/3.73 gears, has new holley blk pump, 12 gallon RCI fuel cell, braided fuel line from front to back, fuel pressure reg w/guage, msd 6al box, msd blaster coil, steeda clutch quadrant and fire wall adj, bbk x pipe, flowmaster mufflers (no tail pipes), new 6 piece head light set, 4" cowl hood w/svo scoop, double hump cross member, drive shaft, radiator w/electric fan, battery box relocated to rear...I even have radiator hoses.. Switches have been wired for fuel, ign, and fan....Jams have been painted, all trim has been put back on... Car has Draglites now, 15x3 and 15x8 w/275 M/T drag radials...Interior has been detailed, spoiler has been painted and put back on.. Car looks freakin awesome... Everything is there but motor and trans...
******Motor*****
Not sure on miles on short block, guy told me 60 miles, i believe it is more than that due to some carbon built up on top of the pistons.... Reguardless, very few miles. I'm not sure of miles on the heads, but appears very little carbon on valves and combustion chambers... Now, motor has not been fired since everything has been install together... The motor has a new solid lift crane cam, 3200-6800 range, new comp push rods, new ford racing timing set, new ford racing head and intake gaskets. The heads have matched springs to the cam, with the inner springs not installed due to cam break-in, that is what is recommended. The motor has 6 quarts of valvoline racing 50 wt, 2 bottles of stp, and 1 bottle of Lucas breakin additive. Cam should break-in properly with this oil concockion.. Motor needs to run for 20 minutes straight @ 2000 rpms, then let engine cool off and your done. I would put some miles on it before putting the inner springs back in to be on the safe side. Valves have been set, oil pump is primed, all bolts are torqued, dist has been properly dropped in. Engine needs serpentine belt, spark plugs and wires to finish!!!!!. Motor is ready to fire..
.060 351
convertable mounts
TRW dished pistons (forged)
C9 Rods and Crank
750 hp carb (literally only 3 passes, no street miles)
Motorsport intake (same as Victor) (drilled and tapped for a fogger system)
MSD Distributor
Windsor Sr. heads 2.05/1.60
ARP head bolts
Harland Sharp 1.6 roller rockers
Comp Valve springs
Comp Push rods
Jegs Alum Valve Covers
Ford Racing gaskets
Ford Racing Timing Set
Crane Cam and Lifters (solid flat, works 3200-6800 rpms)
Ford Racing Oil Pan (Fox Swap)
HV Oil pump
Mac 351 swap Chrome Headers, large tube w/3" ball flange
It would take well over 4k to duplicate, I'm looking for reasonable cash offers or cash offers with trades...
I'm selling cause cant afford to finish the car the route i'm going....
A reasonable offer is going to be above $2500 for all u lowballers out there...
This motor should be a reliable 11 sec setup for an average weight mustang...
*****Transmission*****
C-4 Trans and Hurst Quarterstick w/2 momentary switches, works good, was in a 12.0 sec car with no problems. Not sure what all has been done, but if you have more than 400hp, u better buy a PA or Redneck.. This one is great for street and mild strip. Pan fill, with big bellhousing.
Roller $3000
Engine Best Offer over $2500
Trans and Shifter $400
I may be missing a few things but you get the idea. Texting is best @ 765-541-0577 thanks Troy
****I hope this ad is ok with the Mods**** If not, just delete the roller part please....:bigthumb
http://i249.photobucket.com/albums/gg237/mustang398/3603.jpg
http://i249.photobucket.com/albums/gg237/mustang398/3602.jpg
http://i249.photobucket.com/albums/gg237/mustang398/89droid3.jpg
http://i249.photobucket.com/albums/gg237/mustang398/89droid2.jpg
http://i249.photobucket.com/albums/gg237/mustang398/89hatch5.jpg
*******Roller*******
Solid car, no rust, solid floor pans, solid strut towers. Nice paint, front and rear bumpers need some touch up, and minor damage to bottom of lf fender (behind the tire) Heater box is out but wipers and lights all still work. They sell 12v heaters on ebay that are very reasonable if you want heat back in the car. Has 8.8 w/3.73 gears, has new holley blk pump, 12 gallon RCI fuel cell, braided fuel line from front to back, fuel pressure reg w/guage, msd 6al box, msd blaster coil, steeda clutch quadrant and fire wall adj, bbk x pipe, flowmaster mufflers (no tail pipes), new 6 piece head light set, 4" cowl hood w/svo scoop, double hump cross member, drive shaft, radiator w/electric fan, battery box relocated to rear...I even have radiator hoses.. Switches have been wired for fuel, ign, and fan....Jams have been painted, all trim has been put back on... Car has Draglites now, 15x3 and 15x8 w/275 M/T drag radials...Interior has been detailed, spoiler has been painted and put back on.. Car looks freakin awesome... Everything is there but motor and trans...
******Motor*****
Not sure on miles on short block, guy told me 60 miles, i believe it is more than that due to some carbon built up on top of the pistons.... Reguardless, very few miles. I'm not sure of miles on the heads, but appears very little carbon on valves and combustion chambers... Now, motor has not been fired since everything has been install together... The motor has a new solid lift crane cam, 3200-6800 range, new comp push rods, new ford racing timing set, new ford racing head and intake gaskets. The heads have matched springs to the cam, with the inner springs not installed due to cam break-in, that is what is recommended. The motor has 6 quarts of valvoline racing 50 wt, 2 bottles of stp, and 1 bottle of Lucas breakin additive. Cam should break-in properly with this oil concockion.. Motor needs to run for 20 minutes straight @ 2000 rpms, then let engine cool off and your done. I would put some miles on it before putting the inner springs back in to be on the safe side. Valves have been set, oil pump is primed, all bolts are torqued, dist has been properly dropped in. Engine needs serpentine belt, spark plugs and wires to finish!!!!!. Motor is ready to fire..
.060 351
convertable mounts
TRW dished pistons (forged)
C9 Rods and Crank
750 hp carb (literally only 3 passes, no street miles)
Motorsport intake (same as Victor) (drilled and tapped for a fogger system)
MSD Distributor
Windsor Sr. heads 2.05/1.60
ARP head bolts
Harland Sharp 1.6 roller rockers
Comp Valve springs
Comp Push rods
Jegs Alum Valve Covers
Ford Racing gaskets
Ford Racing Timing Set
Crane Cam and Lifters (solid flat, works 3200-6800 rpms)
Ford Racing Oil Pan (Fox Swap)
HV Oil pump
Mac 351 swap Chrome Headers, large tube w/3" ball flange
It would take well over 4k to duplicate, I'm looking for reasonable cash offers or cash offers with trades...
I'm selling cause cant afford to finish the car the route i'm going....
A reasonable offer is going to be above $2500 for all u lowballers out there...
This motor should be a reliable 11 sec setup for an average weight mustang...
*****Transmission*****
C-4 Trans and Hurst Quarterstick w/2 momentary switches, works good, was in a 12.0 sec car with no problems. Not sure what all has been done, but if you have more than 400hp, u better buy a PA or Redneck.. This one is great for street and mild strip. Pan fill, with big bellhousing.
Roller $3000
Engine Best Offer over $2500
Trans and Shifter $400
I may be missing a few things but you get the idea. Texting is best @ 765-541-0577 thanks Troy
****I hope this ad is ok with the Mods**** If not, just delete the roller part please....:bigthumb