trying to clean out garage

[Flaming87lx]

http://i249.photobucket.com/albums/gg237/mustang398/t-tops.jpg
$100 86 GT t-tops
http://i249.photobucket.com/albums/gg237/mustang398/trannymount.jpg
$10 tranny mount
http://i249.photobucket.com/albums/gg237/mustang398/timingcover2.jpg
$50.00 fi timing cover with new water pump
http://i249.photobucket.com/albums/gg237/mustang398/timingcover1.jpg
$15 fi timing cover
http://i249.photobucket.com/albums/gg237/mustang398/tstathousings.jpg
$5 ea
http://i249.photobucket.com/albums/gg237/mustang398/steering2-1.jpg
http://i249.photobucket.com/albums/gg237/mustang398/steering1-1.jpg
steering column out of 86 gt w/key and aftermarket steering wheel $50
http://i249.photobucket.com/albums/gg237/mustang398/starter-1.jpg
starter off 86 302, works well $20
http://i249.photobucket.com/albums/gg237/mustang398/wheelspacers.jpg
$20 for all
http://i249.photobucket.com/albums/gg237/mustang398/pullies.jpg
$10 serpentine pullies off 86 5.0

[Flaming87lx]

http://i249.photobucket.com/albums/gg237/mustang398/plugwires.jpg
$15 used for about 200 miles 86 302 plug wires
http://i249.photobucket.com/albums/gg237/mustang398/pgshiftsol.jpg
$25 rpm activated shift solenoid for a powerglide
http://i249.photobucket.com/albums/gg237/mustang398/msdnoisefilter.jpg
$10 msd noise filter
http://i249.photobucket.com/albums/gg237/mustang398/msd.jpg
$20, needs send to msd for repair, msd said min $35 to max of $80 for repair
http://i249.photobucket.com/albums/gg237/mustang398/motormounts.jpg
$15 stock 5.0 mounts that have been welded so they are solid mounts
http://i249.photobucket.com/albums/gg237/mustang398/miscstuds.jpg
$20 misc rocker studs

[Flaming87lx]

http://i249.photobucket.com/albums/gg237/mustang398/massairmeter.jpg
$25 good mass air meter for 2000 3.4 venture
http://i249.photobucket.com/albums/gg237/mustang398/hurstbezel.jpg
$20 hurst bezel for a 87-93 fox
http://i249.photobucket.com/albums/gg237/mustang398/fuelfilter.jpg
$15 universal inline (carb style fuel filter)
http://i249.photobucket.com/albums/gg237/mustang398/freezer3.jpg
http://i249.photobucket.com/albums/gg237/mustang398/freezer2.jpg
http://i249.photobucket.com/albums/gg237/mustang398/freezer1.jpg
$75.00 nice working freezer, just do not need anymore
http://i249.photobucket.com/albums/gg237/mustang398/ecm2.jpg
http://i249.photobucket.com/albums/gg237/mustang398/ecm1.jpg
$50 good ecm from 2000 chevy venture
http://i249.photobucket.com/albums/gg237/mustang398/distefi.jpg
$65 86 5.0 dist, module is brand new, dist, cap, rotor used less than 200 miles

[Flaming87lx]

http://i249.photobucket.com/albums/gg237/mustang398/dialin.jpg
$10
http://i249.photobucket.com/albums/gg237/mustang398/dashpanel-1.jpg
$20
http://i249.photobucket.com/albums/gg237/mustang398/fuelpump.jpg
$20 fairly new inline fi fuel pump for 5.0
http://i249.photobucket.com/albums/gg237/mustang398/console2.jpg
http://i249.photobucket.com/albums/gg237/mustang398/console1.jpg
$20 universal center console
http://i249.photobucket.com/albums/gg237/mustang398/collectors.jpg
$10 1 piece 3 1/2 collectors
http://i249.photobucket.com/albums/gg237/mustang398/coil.jpg
$15 stock fi coil
http://i249.photobucket.com/albums/gg237/mustang398/carbspacers.jpg
$5 ea
http://i249.photobucket.com/albums/gg237/mustang398/carbdist.jpg
$15 carb style 5.0 dist
http://i249.photobucket.com/albums/gg237/mustang398/braided2.jpg
$10 braided line

[Flaming87lx]

http://i249.photobucket.com/albums/gg237/mustang398/braided1.jpg
$10
http://i249.photobucket.com/albums/gg237/mustang398/altandbracket2.jpg
http://i249.photobucket.com/albums/gg237/mustang398/altandbracket1.jpg
$50 86 5.0 alt and bracket, (alt was only used for a few hundred mile)
http://i249.photobucket.com/albums/gg237/mustang398/acbypass.jpg
$10 a/c bypass pulley for a sbf truck setup

[Flaming87lx]

need a good running v8 for a ol f150, will do some trading????

[Mustard]

Does the hurst bezzel still have all the tabs? If so I will take it. Where you located?

[Flaming87lx]

One tab is missing. Im north of brookville in

[ryan]

hey troy, how long are those two braided lines? and what sizes are they? would you ship them? thanks

[Flaming87lx]

hey troy, how long are those two braided lines? and what sizes are they? would you ship them? thanks

Yeah I'll ship, i'll get sizes soon

[Flaming87lx]

I returned all pm's and left some messages by phone...... sorry guys, been away from computer for a day or so.... Here's my number for those who want to call me. 765-541-0577 Thanks Troy

[Flaming87lx]

make offers, want it out of my garage