Dart 427 engine

[mustangboy]

Sold my roller and I really was thinking of holding on to this but I think we are buying a new boat so I'm unloading ALL of my mustang stuff. This is the good dart block ready for whatever you can throw at it. It was built for boost but I was going to run it n/a for now which would have been approx 9-1 comp with my vic jr heads. I have almost everything to finish assembling the engine minus the pushrods and a couple gaskets. Here is a quick rundown on the shortblock. I will do $4000 for it as a bare shortblock

IRON EAGLE BLOCK W / BILLET CAPS

EAGLE CRANK AND RODS

DIAMOND PISTONS

ALL ARP HARDWARE

FULLY ASSEMBLED BY BARKER MACHINE

I also have the following but will not part out until the shortblock sells. If someone wants they can buy it all or what they want with the shortblock but like I said I'm not parting till the shortblock sells. All parts are new unless noted

Choice of solid roller turbo or n/a cam both comp cam
Comp link bar solid roller lifters
Arp head stud kit
Moroso 7qt pan and pickup powder coated charcoal gray
one piece oil pan gasket
melling m83 oil pump
ati super dampner
Cloyes 3535x9 timing chain
Cometic head gaskets
Moroso 93060 v/c gaskets
Proform polished slant edge valve covers powder cleared
arp 150-2503 balancer bolt
arp 154-7901 pump shaft
Edelbrock Vic Jr 351 intake converted to efi used but freshly coated silver
felpro 1250 intake gaskets
stock t stat housing coated charcoal
edelbrock fuel rails coated charcoal
new front cover coated silver
new ford motorsport water pump
brand new water pump/front cover bolt kit
bbk 351 swap headers
efi spider intake used and coated flat black
used 101mm accufab t/b used will sell with custom 4" intake pipe and big
k&n filter
42lb and 30lb injectors both used
Edelbrock vic jr heads currently set up with hydraulic springs used
Comp pro magnum rocker arms used
comp 954-16 valve springs for solid roller new
Energy suspension 4-1122g motor mounts
ford m-8511-b351 bracket swap kit to use a/c and p/s

Like I said I have almost everything and may be forgetting a couple of them. Just to mention I still also have my 347 shortblock sitting here as well. Feel free to pm me or call at 513-703-5928. Thanks

[jad0087]

is the block used?

[mustangboy]

No the 427 is completely brand new never run as are most all the parts I have for it.

[mustangboy]

Here is some pics

http://farm8.staticflickr.com/7158/6763365393_13baf67135_b.jpg (http://www.flickr.com/photos/11756743@N02/6763365393/)
427-2 (http://www.flickr.com/photos/11756743@N02/6763365393/) by mustangboy429 (http://www.flickr.com/people/11756743@N02/), on Flickr

http://farm8.staticflickr.com/7032/6763362923_9dfd8b2571_b.jpg (http://www.flickr.com/photos/11756743@N02/6763362923/)
427 (http://www.flickr.com/photos/11756743@N02/6763362923/) by mustangboy429 (http://www.flickr.com/people/11756743@N02/), on Flickr

http://farm8.staticflickr.com/7016/6763360907_91f8f9e49f_b.jpg (http://www.flickr.com/photos/11756743@N02/6763360907/)
427-1 (http://www.flickr.com/photos/11756743@N02/6763360907/) by mustangboy429 (http://www.flickr.com/people/11756743@N02/), on Flickr

[Gearhead]

Damn, that engine is beautiful Kenny !!!! :bigthumb

[1baddlx]

hmmmm i may be able to purchase this....

[mustangboy]

Shortblock is SOLD!!!! Everything else is still available except the turbo cam and Edel Vic jr heads/rockers they are also sold. Over the next couple days I'm gonna put prices on everything but if someone sees something they want feel free to shoot me an offer. Remember all this stuff is brand new in the boxes and I'm willing to deal a little but am not giving stuff away. Look at Jegs and figure I'll take a couple bucks off so don't bother to shoot me offers of half of retail.

[AntiRice427]

Thanks man! Paypal deposit is sent, see you soon!

[MrMustang99GT]

Do you still have the 347 sb? Can you give me details.. Send me a PM.. Thx

[mustangboy]

No problem Mike, you are going to be very happy. Sorry deposit has been taken on the 347 as well so it is sold as well.

[93cobra]

Im happy for you kenny moving your stuff. Sometimes its good to turn over a new leaf enjoying something else for awhile. You can always pick up another hot rod if you miss it etc.

[mustangboy]

Yep there are plenty of cars out there. Pretty much have all the big stuff sold, now just to sell all the smaller stuff. I should be able to stroke the check to pay off the Jeep and then we are picking up a new boat. Things are working out pretty good:bigthumb

[89notch]

Yep there are plenty of cars out there. Pretty much have all the big stuff sold, now just to sell all the smaller stuff. I should be able to stroke the check to pay off the Jeep and then we are picking up a new boat. Things are working out pretty good:bigthumb

What kind of boat you going to buy?

[mustangboy]

Yamaha 242 Limited S jet boat, just like this one

http://farm8.staticflickr.com/7005/6763326345_c60bbcfb04.jpg (http://www.flickr.com/photos/11756743@N02/6763326345/)
242_limited_s_04 (http://www.flickr.com/photos/11756743@N02/6763326345/) by mustangboy429 (http://www.flickr.com/people/11756743@N02/), on Flickr

[89notch]

Yamaha 242 Limited S jet boat, just like this one

http://farm8.staticflickr.com/7005/6763326345_c60bbcfb04.jpg (http://www.flickr.com/photos/11756743@N02/6763326345/)
242_limited_s_04 (http://www.flickr.com/photos/11756743@N02/6763326345/) by mustangboy429 (http://www.flickr.com/people/11756743@N02/), on Flickr

A friend of mine has one of those. Its a very nice boat. I think he is actually selling it or did sell it. I'm not sure if its that exact model or not but its close

[mustangboy]

Yeah the jet boats are suppose to be a bit different than the traditional drive. I told the salesman that I want to drive one before I sign on the dotted line. From what I've read on the jet boat forums guys really love them and seem to be pretty reliable to boot.

[89notch]

Yeah the jet boats are suppose to be a bit different than the traditional drive. I told the salesman that I want to drive one before I sign on the dotted line. From what I've read on the jet boat forums guys really love them and seem to be pretty reliable to boot.

Driving them is a little different but you will adapt. Putting them on the trailer is a little tricky the first few times.

[mustangboy]

Deal pending on the oil pan/pickup:bigthumb

[mustangboy]

I'm gonna try not to start an individual thread for every part so here are a couple things I had pics of already so I'm gonna list them. First a brand new set of the proform slant edge v/c in polished that I did powder clear so you never have to worry about polishing them again. Retail is $214 and coating would be $40 I'll take $200 for them. Next is a Vic Jr spider intake that is used but is freshly powder coated silver stardust w/ clear I will do $300 for it. I have a new set of Edelbrock fuel rails that have been coated charcoal/clear for $100 and the spider elbow that is coated flat black for $100 as well. I have a 101mm Accufab t/b w/ a brand new black silicone coupler I will sell for $200 which will also include the 4" aluminum intake pipe/k&n filter. I'll post up more prices later. Here is some pics

http://farm8.staticflickr.com/7019/6518234143_2364dde3a7_b.jpg (http://www.flickr.com/photos/11756743@N02/6518234143/)
991 (http://www.flickr.com/photos/11756743@N02/6518234143/) by mustangboy429 (http://www.flickr.com/people/11756743@N02/), on Flickr

pic of t/b before the new coupler

http://farm6.staticflickr.com/5123/5261225233_28db300b27_b.jpg (http://www.flickr.com/photos/11756743@N02/5261225233/)
017 (http://www.flickr.com/photos/11756743@N02/5261225233/) by mustangboy429 (http://www.flickr.com/people/11756743@N02/), on Flickr

[SCHMUCKINGHAM]

Kenny, I hate you



How many Vic Jr intakes/elbows/rails do you have!

[mustangboy]

:D More than I need!!

[mustangboy]

Here is a pic of the cam box w/ the specs. Still in plastic never even opened. It is for a solid roller. Just paid $295 plus tax. Also pictured is the valve springs that I was going to use with this cam on my Vic Jr heads. Paid $129 plus tax.
I will do $275 and $120 firm for each of them. I had $44 in tax and shipping for them so price is firm.

http://farm8.staticflickr.com/7015/6772394667_ef5c3436be_z.jpg (http://www.flickr.com/photos/11756743@N02/6772394667/)
007 (http://www.flickr.com/photos/11756743@N02/6772394667/) by mustangboy429 (http://www.flickr.com/people/11756743@N02/), on Flickr

http://farm8.staticflickr.com/7163/6772399339_b15412aafd_z.jpg (http://www.flickr.com/photos/11756743@N02/6772399339/)
009 (http://www.flickr.com/photos/11756743@N02/6772399339/) by mustangboy429 (http://www.flickr.com/people/11756743@N02/), on Flickr

[Gearhead]

I'm gonna try not to start an individual thread for every part so here are a couple things I had pics of already so I'm gonna list them. First a brand new set of the proform slant edge v/c in polished that I did powder clear so you never have to worry about polishing them again. Retail is $214 and coating would be $40 I'll take $200 for them.
http://farm8.staticflickr.com/7019/6518234143_2364dde3a7_b.jpg (http://www.flickr.com/photos/11756743@N02/6518234143/)



V/C's baffled ??

[mustangboy]

Yes they have baffles

[mustangboy]

Deal pending on throttle body and elbow!!

[mustangboy]

Elbow and t/b are SOLD!!

[mustangboy]

The water pump, timing cover bolt set and motor mounts are sold!!

[mustangboy]

Valve covers are SOLD!! Going to hawaii

[Timido]

Nice to meet you guys. Antirice that is a great shortblock you got a smoking deal on that.

[mustangboy]

Engine is on its way to its new home. Thanks Mike and if you need anything else let me know.

[AntiRice427]

Thanks guys! Nice to meet both of you.

[mustangboy]

Btw the Moroso oil pan/pickup and front cover are sold!! Also the 30lb injectors and oil pump drive are sold as well. Thanks everyone!!