Parse error: syntax error, unexpected '<' in /opt/bitnami/apache2/htdocs/forums/archive/global.php(117) : eval()'d code on line 1
New heads [Archive] - StangBangerz Forums
PDA

View Full Version : New heads


cyah92
10-08-2017, 08:37 PM
Looking at the 235cc r heads. What you think about them. Is there a better head for around the same price.
draggin50
10-08-2017, 10:24 PM
It all depends on what you are looking to do. Best bet is to call Fox Lake up or someone who specializes in cylinder heads and tell him your plans and he will recommend one for you.
Rick93coupe
10-08-2017, 10:41 PM
Buy a highport, in whatever CC runner you need, for the power you want to make.
cyah92
10-09-2017, 07:14 PM
I'm building a blow through supercharged set up but going to use the engine until I can get the money for the supercharger
draggin50
10-09-2017, 08:12 PM
Whats wrong with your old engine? Seems like that would've been a good motor to get some passes under your belt and the rest of the car sorted out.
cyah92
10-09-2017, 08:45 PM
Me and e85 never got along. Melted two pistons. Heads needs a little work to get them back up to par. A lot of bad luck came my way so decided to get rid of everything and start with a fresh setup.
cyah92
10-09-2017, 08:48 PM
I ran the car but some reason it kept popping around 5k and we thought maybe it was ignition issue so I thought it was figured out so the last time I took it out it did it again and that's when it fried two pistons. Block might be shot as well. It was running really lean on the top end. Don't know if the new pump went or had a line collapse. It sucks but I will get over it and move on.
draggin50
10-09-2017, 09:05 PM
Did not know that. That sucks but like you said, move on and start fresh. Hope you have better luck next time and you are able to salvage some of your old parts.
2Fast4You
10-10-2017, 04:25 PM
Looking at either the Trickflow R head or HighPorts.
draggin50
10-10-2017, 04:48 PM
+1 for the highports!
2Fast4You
10-10-2017, 07:56 PM
Yup, that's what I was telling him yesterday.
Rick93coupe
10-11-2017, 09:21 AM
Ed Curtis has a nice cnc package with upgraded valvetrain.
2Fast4You
10-11-2017, 01:43 PM
Ed Curtis has a nice cnc package with upgraded valvetrain.

Thanks for the insight Rick.
adragon72
10-11-2017, 02:07 PM
All this talking about head just reminds me that I sure need some too. Sucks that it cost so much.
draggin50
10-11-2017, 02:59 PM
All this talking about head just reminds me that I sure need some too. Sucks that it cost so much.

Head or heads??? LOL!!!
adragon72
10-11-2017, 03:16 PM
Well I wasn't thinking dirty but I guess im probably in the need of both.LMAO
Rick93coupe
10-11-2017, 07:28 PM
Thanks for the insight Rick.

No prob. I've looked at these a couple of times now.

http://www.flowtechinduction.com/tfs-sbf-high-port-cnc-230hr-street-beast-heads/
draggin50
10-11-2017, 07:55 PM
No prob. I've looked at these a couple of times now.

http://www.flowtechinduction.com/tfs-sbf-high-port-cnc-230hr-street-beast-heads/

I may have missed it but what kind of flow numbers on those?
Rick93coupe
10-11-2017, 08:49 PM
I may have missed it but what kind of flow numbers on those?

He doesn't have them listed but if you check out fox lakes listing, they're going to be similar in flow numbers.

http://foxlakeracing.davidnew.net/site/products-and-services/cylinder-heads-302-351-windsor/tfs-high-port-heads/