Your not supposed to be looking at the blower Aaron. LolQuote:
Originally Posted by k062693w
Printable View
Your not supposed to be looking at the blower Aaron. LolQuote:
Originally Posted by k062693w
You don't think it does already Walter?Quote:
Originally Posted by Walter
More to follow soon.
New spacerhttps://uploads.tapatalk-cdn.com/201...e92f1ba0f2.jpg
Sent from my Z965 using Tapatalk
Had to weld a bung onto the radiator for the water temp sending unit. https://uploads.tapatalk-cdn.com/201...0c8d41d3ca.jpg
Sent from my Z965 using Tapatalk
Do you run a thermostat?
Nice! You running that under the nitrous plate or are you planning on running a fogger?
I am not Walter.Quote:
Originally Posted by Walter
Sent from my Z965 using Tapatalk
I will be running a single stage plate Brian.Quote:
Originally Posted by draggin50
Sent from my Z965 using Tapatalk
There is no thermostat housing on this intake, each water jacket is ran with a -12 braided line. I can always install restrictors if needed. https://uploads.tapatalk-cdn.com/201...4e082f9743.jpg
Sent from my Z965 using Tapatalk
Either way, it sure looks good!!
I would like to plumb my carb spacer with the nitrous spray bars.Quote:
Originally Posted by draggin50
Sent from my Z965 using Tapatalk
This thing has been sitting way to long!!! You have to be almost ready to make some passes!!!
Whats left?
I've ran into a couple issues, hopefully be able to soon.
What happenedQuote:
Originally Posted by 2Fast4You
You're gonna miss out on some good weather coming up!!!
Had to pull the trans back out do to a leaking shifter shaft seal, that meant the whole exhaust had to come out as well etc.Quote:
Originally Posted by Walter
Sent from my Z965 using Tapatalk
Should've tried some flex seal!!!
Sucks though that it had to come back out to fix one small problem. Nothing is ever easy.
It was a bad leak, not sure anything would have helped other than replacing it. It was inevitable, it was easier to just fix it now. Just typing about makes it sounds easy, but when your car is only inches off of the concrete floor, it's another whole story. It should be out soon though.
Had some throttle linkage issues as well, I hope this helps. I couldn't get the throttle past 3/4 of the way, this will raise the point at which it was able to mount before. It also gives me a little more travel on the throttle, time will tell. https://uploads.tapatalk-cdn.com/201...ce3536e37d.jpg
Sent from my Z965 using Tapatalk
Minor updates to follow.
Replacing these mikd steel uppers with these Racecraft billet uppers, should be a good upgrade over them. https://uploads.tapatalk-cdn.com/201...7695859f05.jpghttps://uploads.tapatalk-cdn.com/201...be56973697.jpg
Sent from my Z965 using Tapatalk
Wonder what the strength difference is in those? They look nice!
Not absolutely sure about that, it was a recommendation from Rob at Rogue Racecars, so I did it.Quote:
Originally Posted by draggin50
Sent from my Z965 using Tapatalk
Just looked on their website and saw they are billet steel. I thought they was billet aluminum. Guess that answers my question.
CorrectQuote:
Originally Posted by draggin50
Sent from my Z965 using Tapatalk
Those are nice looking pieces. I'm still rocking the old school HPM uppers.
I will have the others up for sale once they have been replaced, if your looking to upgrade Rick.
You won't see any difference, just fancy looking is all.
And that could very well be true.Quote:
Originally Posted by Walter
But when you put nitrous to it, they wont flex or break. So good insurance in my book. Those look good! I just have jegster uppers.
Sent from my iPhone using Tapatalk
Thanks Steve, your absolutely correct about insurance.Quote:
Originally Posted by S281SC
It was a recommendation to insure no deflection in that area of the controls arms, I doubt that it is going to do anything to improve anything else.
He's going to have to when Two-tone, Walter, and Silver Bullet roll on the scene looking to get on the list this spring...assuming they have an interest.
Sure, something like that.Quote:
Originally Posted by redfirepearlgt
Sent from my Z965 using Tapatalk
Actually shayne, you are going to have to worry about me before those guys can make their way up the list to you. I am going to try out a gasket matched intake before the season is over. Should give me a little boost and let me spray a little more. Its on like donkey kong brother.... haha
Stick shifts for the win! I notice we are outnumbering you auto guys at the top of the list. Better watch out. :)
Sent from my iPhone using Tapatalk
I have one of each this year. The stick car is still quicker though... Just for this year!
It's all about having fun with friends, let's do it.
Sent from my Z965 using Tapatalk
Im game!
You better put the big pills in......Quote:
Originally Posted by S281SC
When u gonna be back out?Quote:
Originally Posted by 2Fast4You