Need parts for the Stangbangerz.com Pinks Build please help if you can

[86NotchGT]

Kelly i have 3 2 1/2" 90 degree mandrel bends.It's not much but there yours if you can use them.Also some new 5 lug rotors.Let me know.

[89notch]

Kelly i have 3 2 1/2" 90 degree mandrel bends.It's not much but there yours if you can use them.Also some new 5 lug rotors.Let me know.

can use the 5 lug rotors and bends for sure. Thanks


We also need some 5 lug 31 spline c clip axles. We have a chance to trade the 31spline setup we have for a 33 spline spool setup.

[89notch]

UPDATED PARTS LIST

Parts Needed

7/16 rockers
Pushrods(unknown on length)
Complete engine gasket set
Oil pump
Oil pan
Powerglide driveshaft
31 spline 5 lug axles c clips
5 lug read disk brakes
5 lug front rotors and bigger brakes
Manual Rack and steering shaft
Misc gray interior parts Carpet door panels, seats etc
Maybe some aftermarket seats
Throttle Body
Injectors(60lbs) I think Mod Depot is working on these
A9l Harness and computer

And lots of other small things I will be adding later

[bobtsgt]

I have 96 GT single piston front calipers (still worked when pulled 1 week ago), rotors (probally need turned), 96gt rear pads and rotors with about 300 miles on them. do you need one seat or 2?

[89notch]

I have 96 GT single piston front calipers (still worked when pulled 1 week ago), rotors (probally need turned), 96gt rear pads and rotors with about 300 miles on them. do you need one seat or 2?

That will work great we will just have to find some rear backing plates and have them machined for the C clips elims

[quik lx]

I have a bunch of grey interior plastics parts and 1 good grey passenger side power door panel you can have.

[orangedemon331]

What about a K member and some A arms??????????? Also what about the battery box you still need one or not??

[89notch]

Have a complete UPR front and Rear suspension kit on the way I also have the battery box covered.

We do need front struts and rear shocks though

[Jeff88coupe]

I have my original stock grey carpet out of my coupe. I had Keith Decker clean it..don't look to bad. It just has a few cutouts for my 6pt bar. If you want it let me know..I'll get it dropped off at cincy speed.

[89notch]

Sure but I might want to pick that up I'm going to try to not clutter up craigs store with big stuff

[bobtsgt]

I'll drop off what I got at Craig's either tomorrow on Friday afternoon

[PonymanfiveO]

Im sure I have an extra A9L and a harness piece to turn a non mass air car into a mass air car. If you can get your hands on a non Mass air harness I'll gonate all if it.

[89notch]

Im sure I have an extra A9L and a harness piece to turn a non mass air car into a mass air car. If you can get your hands on a non Mass air harness I'll gonate all if it.

Anyone have a speed density harness? Looks like Matt is going to hook us up with the rest

[bobtsgt]

brake parts are at Cincy

[89notch]

brake parts are at Cincy

Great thanks anyone else have anything that will help?

[IWRBB]

I have 2 used Cobra rear rotors you can have. They look like they are in good shape. You'd need the right brackets to run the thicker rotors though. Something off a Mach 1 or a 94-98 Cobra. The Cobra have the same rear caliper as a GT though.

[89notch]

Bump anyone else

[ricmcusa]

F.Y.I as far as seats go. If you want something easy to install and fairly light 2000 cavalier seats bolt to the mustang tracks. They look good to. No one will ever know there from a chevy.

[89notch]

BUMP still need a lot of stuff the car must be complete and running before powerfest since the producers is coming to check the car out then

[plated]

any help will go along way you guy's.if u can donate any money or parts please do,this is a really big project and we need all the help that we can get