http://stangbang.tripod.com/ Where all this began!
http://stangbang.tripod.com/twisted/ Vinny
1984 Mustang build @craig_btr on Instagram
The believe the rear end has been cut down a total of 3-1/4" on each side.
I finally got the Stang off the trailer and in the garage.
Looking at everything I have to do, Overwhelmed would be a good status update.
Its going to be a lot of Long nights out here in the garage this Winter.
http://stangbang.tripod.com/ Where all this began!
http://stangbang.tripod.com/twisted/ Vinny
1984 Mustang build @craig_btr on Instagram
Done yet? Get on it!!!
I am so far out on this build.
http://stangbang.tripod.com/ Where all this began!
http://stangbang.tripod.com/twisted/ Vinny
1984 Mustang build @craig_btr on Instagram
I said to myself, "this Coyote isnt going to change the Valve springs itself."
SO I fired up the heater and went to work...
Once I get everything apart and cleaned up, Ill be selling off the parts I wont be using anymore..so be looking for that post.
http://stangbang.tripod.com/ Where all this began!
http://stangbang.tripod.com/twisted/ Vinny
1984 Mustang build @craig_btr on Instagram
http://stangbang.tripod.com/ Where all this began!
http://stangbang.tripod.com/twisted/ Vinny
1984 Mustang build @craig_btr on Instagram
Made an early mroning run up to Cam's shop to have hime Tig some -12 fittings on my new Ford Valve covers.
Im hoping to have my New, Gen II Camshafts in this week. Then I can get them installed along with some PAC 1234X springs and get the eng/trans back under the car.
Thanks for tuning in.
http://stangbang.tripod.com/ Where all this began!
http://stangbang.tripod.com/twisted/ Vinny
1984 Mustang build @craig_btr on Instagram
Just plugging away out in the garage.
http://stangbang.tripod.com/ Where all this began!
http://stangbang.tripod.com/twisted/ Vinny
1984 Mustang build @craig_btr on Instagram
Shit. I have A LONG way to go with this. Its like Im completely starting over.
Oh well, Ill just keep on Keeping on....
I got the drivers side cams installed along with the chains.
ARP Head studs & Cometic HGs installed.
I got the pass side done as well, but when I went to turn it ove, its said, NOPE. So Ill be watching my YT videos again and seeing where I fucked up.
http://stangbang.tripod.com/ Where all this began!
http://stangbang.tripod.com/twisted/ Vinny
1984 Mustang build @craig_btr on Instagram
I have been fucking with these for a couple weeks now and I finally double checked my order....Seems like Im a Dumbass and ordered the wrong cams.
My dude, Walter to the rescue!! He has a set and he is getting them sent out so that I can get this back together!
Hopefully Ill have some new updated pics soon.
http://stangbang.tripod.com/ Where all this began!
http://stangbang.tripod.com/twisted/ Vinny
1984 Mustang build @craig_btr on Instagram
Awesome build. Excellent welding skills. Hope you figure out the cam issue. I came here today for nostalgia reasons. Looking up old threads I was a parts of. Always loved the forums especially this one and the Dayton 5.0 one that Mike Bell had. Forget the name. Think the name changed once. Wish we could go back. I hate Facebook. Seems like a chaotic mess, cant find things twice half the time. This is a 40 page thread that I can read like a book, find it easily and check in as often as I like. So nice.
I check on this board everyday, but when there are no New posts, I get disappointed as I to remember when there would be quite a few every morning.
http://stangbang.tripod.com/ Where all this began!
http://stangbang.tripod.com/twisted/ Vinny
1984 Mustang build @craig_btr on Instagram
http://stangbang.tripod.com/ Where all this began!
http://stangbang.tripod.com/twisted/ Vinny
1984 Mustang build @craig_btr on Instagram
Not a lot going on with anything, but I did get my parts back from PC.
The color really POPS in the Sun.
It looks a bit darker in the shade.
I got around to getting the Glasstek hood a bit closer to installed.
JPC makes a Beefy Flexplate.
and it fits nicely to my Circle D Bolt-together TQ converter.
Which fits nicely into my TSI Built PG 5000.
Not sure when this car will be back together, but at least it will look cool sitting there collecting dust.
http://stangbang.tripod.com/ Where all this began!
http://stangbang.tripod.com/twisted/ Vinny
1984 Mustang build @craig_btr on Instagram
There are currently 1 users browsing this thread. (0 members and 1 guests)