Clay City, 2 hours
Edgewater, 2 1/2 hours
Beech Bend, 2 hours
Ohio Valley (1/8 mile), 1 hour
http://stangbang.tripod.com/ Where all this began!
http://stangbang.tripod.com/twisted/ Vinny
1984 Mustang build @craig_btr on Instagram
Plan on running some UMTR events this year?
http://stangbang.tripod.com/ Where all this began!
http://stangbang.tripod.com/twisted/ Vinny
1984 Mustang build @craig_btr on Instagram
Its home...
and I already got it up in the air to get this DONE!
Even slicing my finger with a razor blade, I still managed to get some brake lines run and the battery cable routed. Once I get all the underneath stuff finished, I can then concentrate on getting the wiring finished up. I dont think I can remember being so happy to shed blood yet continue on to get a project running.
http://stangbang.tripod.com/ Where all this began!
http://stangbang.tripod.com/twisted/ Vinny
1984 Mustang build @craig_btr on Instagram
That had to hurt! Sounds like your dedicated to finishing!
Joe
Craig, remember when u posted that pic of gashing your leg with that angle grinder?
http://stangbang.tripod.com/ Where all this began!
http://stangbang.tripod.com/twisted/ Vinny
1984 Mustang build @craig_btr on Instagram
More progress...
[
3/16 hard line and -2 Teflon line (w/-3 ends)
Strange Brakes and Dbl Adj shocks
Rear end is loaded up with 33 spline axles, Spool and a 4.30 gear and ready to go! Im ordering my Aluminum DS today, so hopefully Ill be able to stop and roll next week!
Thanks for tuning in!
http://stangbang.tripod.com/ Where all this began!
http://stangbang.tripod.com/twisted/ Vinny
1984 Mustang build @craig_btr on Instagram
Beautiful work Craig. I envy your talent and patience. I would have lost interest by now and sold it. LOL!
http://stangbang.tripod.com/ Where all this began!
http://stangbang.tripod.com/twisted/ Vinny
1984 Mustang build @craig_btr on Instagram
Made some more progress the past couple days.
Finished painting the trunk area
Got some cardboard from the recycling bin
Made a template for the spare tire well cover
Got a Black cover from LMR
After some trimming, I got it where I need it. Ill place this ontop of some ACC Saddle Auto carpet and cut around it.
I realized that poster board is easier to work with.
Took some rough measurements and made an outline
First attempt, not to bad
Added some material and some more cuts
and got it close enough
So I then placed it on some cardboard
BAM!
Now all I have to do is get some 3M spray glue and wrap it, with the tan headliner material, (found at Joanns Fabrics) and install it!
Thanks for tuning in!
http://stangbang.tripod.com/ Where all this began!
http://stangbang.tripod.com/twisted/ Vinny
1984 Mustang build @craig_btr on Instagram
Nice work! You putting the fabric right onto the cardboard?
1992 Mustang LX Coupe, 302, PA C4 and On3 70mm.
1993 Reef Blue hatch, 347, 3550, and a kit.
1992 Gould GT project...
http://stangbang.tripod.com/ Where all this began!
http://stangbang.tripod.com/twisted/ Vinny
1984 Mustang build @craig_btr on Instagram
Nice work Craig!
I'd do Masonite over the cardboard tho
http://stangbang.tripod.com/ Where all this began!
http://stangbang.tripod.com/twisted/ Vinny
1984 Mustang build @craig_btr on Instagram
I didnt think this wouldve been as big of a deal as it was. But it sucked trying to contort my big ass around these bars to make sure that they got fully covered with paint.
Im not happy with my color selection, so Ill head to Lowes today and hopefully find a better color.
http://stangbang.tripod.com/ Where all this began!
http://stangbang.tripod.com/twisted/ Vinny
1984 Mustang build @craig_btr on Instagram
Looking Good! Can't wait to see the car finished and the numbers it lays down!!
2008 2019 2020 2021 2022 #1 Of The Dirty Dozen
2018 #2 Of The Dirty Dozen
2024…. Changes coming! How much HP? ALL OF IT!
There are currently 4 users browsing this thread. (0 members and 4 guests)