Results 1 to 20 of 20

Thread: Grey Mare - S197 Turbo 3V Holley Terminator X Max Final Dyno run

  1. #1
    Join Date
    Jul 2016
    Location
    Troy , OH
    Posts
    476

    Grey Mare - S197 Turbo 3V Holley Terminator X Max Final Dyno run

    Final dyno run before I took it to get the 8.50 cage installed. Decided while it is there to have Jason convert the exhaust to a 4" bumper exit as well. Will put it back on the dyno after that.

    495 HP / 505 TQ on 14.3 psi (10 spring / 5 psi dome commanded) on a non-lockup converter.

    https://youtu.be/FntuB38C-Eg
    LS Swapped - Locally hated now

  2. #2
    Join Date
    Aug 2007
    Location
    In a Van By the River !!!
    Posts
    4,670
    Nice !!!
    Aaron


    F**K Photobucket !!!

  3. #3
    Join Date
    Feb 2004
    Location
    Springboro, OH
    Posts
    6,275
    Want to note that this should have been much higher but his full exhaust acts like someone stuck a potato in it at 4500-5k. Should be an animal after Jason works his magic and my tune can do its thing.
    Last edited by NXcoupe; 05-31-2020 at 01:51 PM.

  4. #4
    Join Date
    Jan 2009
    Location
    Hillsboro, Ohio
    Posts
    7,916
    Quote Originally Posted by NXcoupe View Post
    Want to note that this should have been much higher but his full exhaust acts pike someone stuck a potato in it at 4500-5k. Should be an animal after Jason works his magic and my tune can do its thing.
    We've seen what an exhaust can do to a turbo car. Crazy!
    1992 Mustang LX Coupe, 302, PA C4 and On3 70mm.
    1993 Reef Blue hatch, 347, 3550, and a kit.
    1992 Gould GT project...

  5. #5
    Join Date
    Jan 2008
    Posts
    8,828
    very very nice

  6. #6
    Join Date
    Jul 2016
    Location
    Troy , OH
    Posts
    476
    Thanks Chad.
    LS Swapped - Locally hated now

  7. #7
    Join Date
    Feb 2004
    Location
    Carlisle
    Posts
    3,777
    Nice what size exhaust is on it now?
    2013 f150 FX4 ecoboost
    95 Lightning-Vortech
    89 Vert-GT40-P Motor, Exhaust, 4.10 gear on Bullets
    99 Baja Outlaw BES 510bbc ATI procharger

  8. #8
    Join Date
    Feb 2004
    Location
    Fayetteville
    Posts
    1,873
    Did you make the pulls with the air filter on the turbo still?
    2014 CTS V-sport
    2006-teen Black CCSB Powerstroke

  9. #9
    Join Date
    Jul 2016
    Location
    Troy , OH
    Posts
    476
    JIMS SVT - There is no air filter on the turbo - just a turbo guard screen.

    89notch - its 3" coming off the manifolds then back to the stock over axle tubes and then FRPP GTA mufflers.
    LS Swapped - Locally hated now

  10. #10
    Join Date
    Feb 2004
    Location
    Fayetteville
    Posts
    1,873
    Quote Originally Posted by gzbs197 View Post
    JIMS SVT - There is no air filter on the turbo - just a turbo guard screen.

    89notch - its 3" coming off the manifolds then back to the stock over axle tubes and then FRPP GTA mufflers.
    Have you tried to remove it? I had a issue years ago with a screen on my turbo.
    2014 CTS V-sport
    2006-teen Black CCSB Powerstroke

  11. #11
    Join Date
    Feb 2004
    Location
    Carlisle
    Posts
    3,777
    Quote Originally Posted by gzbs197 View Post
    JIMS SVT - There is no air filter on the turbo - just a turbo guard screen.

    89notch - its 3" coming off the manifolds then back to the stock over axle tubes and then FRPP GTA mufflers.
    I made right at 1k to the tire with a 3 inch downpipe all the way back to tailpipes. I think your problem might be that 68mm exhaust wheel. The 4 inch exhaust won't hurt but I would be willing to bet that 68mm is causing some serious back pressure.
    2013 f150 FX4 ecoboost
    95 Lightning-Vortech
    89 Vert-GT40-P Motor, Exhaust, 4.10 gear on Bullets
    99 Baja Outlaw BES 510bbc ATI procharger

  12. #12
    Join Date
    Jul 2016
    Location
    Troy , OH
    Posts
    476
    Quote Originally Posted by JIMS SVT View Post
    Have you tried to remove it? I had a issue years ago with a screen on my turbo.
    it dyno'd pretty close to the same with no screen on the stock ECU on a locked converter. There is a 4" pipe that goes to where the factory airbox was to get cool air from the fender. I don't think it is causing an issue currently.
    LS Swapped - Locally hated now

  13. #13
    Join Date
    Jul 2016
    Location
    Troy , OH
    Posts
    476
    Quote Originally Posted by 89notch View Post
    I made right at 1k to the tire with a 3 inch downpipe all the way back to tailpipes. I think your problem might be that 68mm exhaust wheel. The 4 inch exhaust won't hurt but I would be willing to bet that 68mm is causing some serious back pressure.
    It could be. The plan is to replace the turbo after the motor is built - right now that 68 will make more than enough boost to send a rod out the SBE. Decided to do the 4 inch now since it was at fab and same time down the road. Plus it add's the "cool factor" as well.
    LS Swapped - Locally hated now

  14. #14
    Join Date
    Feb 2004
    Location
    Springboro, OH
    Posts
    6,275
    I guess we'll see what the issue was after the exhaust work is finished. You guys have probably never seen a 3V turbo kit before, they have about 3 times the hot side tubing of a normal turbo kit and his mufflers were not straight thru mufflers.

  15. #15
    Join Date
    Feb 2004
    Location
    Fayetteville
    Posts
    1,873
    Quote Originally Posted by NXcoupe View Post
    You guys have probably never seen a 3V turbo kit before.
    I built one that was the first to go 8’s and eventually went 7.89
    2014 CTS V-sport
    2006-teen Black CCSB Powerstroke

  16. #16
    Join Date
    Feb 2004
    Location
    Springboro, OH
    Posts
    6,275
    Nice! This probably isn't like the one you built. This is similar to an On3 kit, if you've ever seen one of those.

  17. #17
    Join Date
    Jan 2008
    Posts
    8,828
    Quote Originally Posted by JIMS SVT View Post
    I built one that was the first to go 8’s and eventually went 7.89
    NICE!

  18. #18
    Join Date
    Feb 2004
    Location
    Carlisle
    Posts
    3,777
    Quote Originally Posted by gzbs197 View Post
    It could be. The plan is to replace the turbo after the motor is built - right now that 68 will make more than enough boost to send a rod out the SBE. Decided to do the 4 inch now since it was at fab and same time down the road. Plus it add's the "cool factor" as well.
    I would put a 999.00 ls7675 on it I bet it fixes it. I bet your back pressure is sky high with the 68mm wheel.
    2013 f150 FX4 ecoboost
    95 Lightning-Vortech
    89 Vert-GT40-P Motor, Exhaust, 4.10 gear on Bullets
    99 Baja Outlaw BES 510bbc ATI procharger

  19. #19
    Join Date
    Jan 2009
    Location
    Hillsboro, Ohio
    Posts
    7,916
    Quote Originally Posted by 89notch View Post
    I would put a 999.00 ls7675 on it I bet it fixes it. I bet your back pressure is sky high with the 68mm wheel.
    Those are hard to beat really for the price. I was gonna pick one up myself.
    1992 Mustang LX Coupe, 302, PA C4 and On3 70mm.
    1993 Reef Blue hatch, 347, 3550, and a kit.
    1992 Gould GT project...

  20. #20
    Join Date
    Jul 2016
    Location
    Troy , OH
    Posts
    476
    I don’t know if a new turbo will be in budget for this year. That 8.50 cage and install is about going to tap me out.
    LS Swapped - Locally hated now

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •