Or a wanna be race car that sits on jackstands forever .... ask me how I know lolOriginally Posted by Walter
Jack Stand Racing League
Or a wanna be race car that sits on jackstands forever .... ask me how I know lol
Greg
Midnight Mafia
Registered User
Walter removing the interior to put a cage in his street car is what he is saying I think.
1992 Mustang LX Coupe, 302, PA C4 and On3 70mm.
1993 Reef Blue hatch, 347, 3550, and a kit.
1992 Gould GT project...
Registered User
Wasn't sure if he was trying to insinuate that pulling the interior for a cage makes it a race car like his or not...
If money is no object a full cage can be installed while retaining a full interior. I believe Silver Bullet and Beefcake both have certified caged cars with full interiors in them.
Starting all over, Again!
Just saying that the interior has to come out for the roll cage, so there is his weight reduction Chad mentioned earlier, that's all. Walter can then elect whether it goes back in or not. Unfortunately, removing the interior and adding a roll cage will put him back to where he was prior to removing the interior in either direction he goes, which leaves him looking for that 8 second pass, which I know will happen, one way or another. Walter is on a mission! Go get it!
Sent from my Z965 using Tapatalk
#9 2011 Spring Street Car Shoutout
1991 Mini Tubed Mustang Coupe, in the works.
351W base, PG, Stock Suspension chassis
Starting all over, Again!
Intake is back, the flow results are in, it looks like additional HP this coming season.
Sent from my Z965 using Tapatalk
#9 2011 Spring Street Car Shoutout
1991 Mini Tubed Mustang Coupe, in the works.
351W base, PG, Stock Suspension chassis
slow ride..
Might as well order a new rear bumper too!!!Intake is back, the flow results are in, it looks like additional HP this coming season.
Sent from my Z965 using Tapatalk
Starting all over, Again!
Let's hope that isn't the case, going to try and have it set to go straight out, instead of straight up.
Sent from my Z965 using Tapatalk
#9 2011 Spring Street Car Shoutout
1991 Mini Tubed Mustang Coupe, in the works.
351W base, PG, Stock Suspension chassis
Registered User
Go straight for the .040 jet and call it a day! Cant be skeered now!
1992 Mustang LX Coupe, 302, PA C4 and On3 70mm.
1993 Reef Blue hatch, 347, 3550, and a kit.
1992 Gould GT project...
Starting all over, Again!
Hahaha, I'm already skeered and I don't even have the intake back on the car yet, but in the process as I'm typing this.
#9 2011 Spring Street Car Shoutout
1991 Mini Tubed Mustang Coupe, in the works.
351W base, PG, Stock Suspension chassis
Registered User
I can make out the left hand columns on both charts. What are the right hand columns on the upper chart for.
Adding a theoretical 452HP with a .040? I did read that correctly, right? Dude! Start off with the .028". You aren't Sylvester that Cat so you don't have 9 lives. Heck I would have thought you would have started with a 100 HP hit first. Looking forward to seeing it run.
Starting all over, Again!
Fuel flow at PSI on the top chart and fuel/nitrous ratio at PSI on the bottom, from what I understand.
Sent from my Z965 using Tapatalk
#9 2011 Spring Street Car Shoutout
1991 Mini Tubed Mustang Coupe, in the works.
351W base, PG, Stock Suspension chassis
Starting all over, Again!
Chad, I am starting with the 250hp shot utilizing a progressive nitrous controller, that gives me some room for tunability.
Sent from my Z965 using Tapatalk
#9 2011 Spring Street Car Shoutout
1991 Mini Tubed Mustang Coupe, in the works.
351W base, PG, Stock Suspension chassis
Registered User
250??? That's for stock 5.0's...
I thought you was gonna try to outrun a few of these street cars this coming year!
1992 Mustang LX Coupe, 302, PA C4 and On3 70mm.
1993 Reef Blue hatch, 347, 3550, and a kit.
1992 Gould GT project...
Starting all over, Again!
That's always the challenge, I have to start somewhere.
Sent from my Z965 using Tapatalk
#9 2011 Spring Street Car Shoutout
1991 Mini Tubed Mustang Coupe, in the works.
351W base, PG, Stock Suspension chassis
Registered User
I hear ya. Baby steps. No reason to make Darlene an in home nurse for a vegetable.
Starting all over, Again!
Yup, she already tells me that I'm crazy, who am I to argue. hahaha
#9 2011 Spring Street Car Shoutout
1991 Mini Tubed Mustang Coupe, in the works.
351W base, PG, Stock Suspension chassis
Starting all over, Again!
It's back, what will this bolt on really do from Induction Solutions X275 kit?
Sent from my Z965 using Tapatalk
#9 2011 Spring Street Car Shoutout
1991 Mini Tubed Mustang Coupe, in the works.
351W base, PG, Stock Suspension chassis
wheels up
Thats sweet looking
Sent from my SM-G965U using Tapatalk
Starting all over, Again!
So, I finally got to use the lift for the first time, and to install my Billet Racecraft upper controls arms at that. Win, Win...
#9 2011 Spring Street Car Shoutout
1991 Mini Tubed Mustang Coupe, in the works.
351W base, PG, Stock Suspension chassis
Starting all over, Again!
Slight differences between them.
Sent from my SM-G975U1 using Tapatalk
#9 2011 Spring Street Car Shoutout
1991 Mini Tubed Mustang Coupe, in the works.
351W base, PG, Stock Suspension chassis
There are currently 2 users browsing this thread. (0 members and 2 guests)
Posting Permissions
Reply With Quote
