Before & After

[Walter]

LOL

[Maximus]

Got some work done in the garage this weekend.


Getting all this to work together should be fun.:confused:
https://farm8.staticflickr.com/7802/47411706671_4cbb2b6487_b.jpg

Found an old Ford wiring book for the 84 Mustang, so its going to be a huge help.
https://farm8.staticflickr.com/7865/47411706651_ea9ca8454d_b.jpg

Ill have to figure out the Speed sensor to Tremec, so that the Speedo actually works.
https://farm8.staticflickr.com/7899/47411706631_699ee6cb1c_b.jpg

I removed the dash so that I could run wires and hook up connectors easier.
https://farm8.staticflickr.com/7827/47411706541_b0306f53d9_b.jpg

https://farm8.staticflickr.com/7867/47411706491_28e50f3c36_b.jpg


Notice the custom, one off, Hyd clutch pedal assembly.
https://farm8.staticflickr.com/7863/47411706471_9c2db75753_b.jpg

https://farm8.staticflickr.com/7841/47411706451_0056130da4_b.jpg

Started running the wires
https://farm5.staticflickr.com/4824/47411706591_326e4fe020_b.jpg

Once I get the ECM mounted, all this will clean up.
https://farm8.staticflickr.com/7881/47411706391_e2100fcdd8_b.jpg

Mounted the fuse block and re-used a factor grommet & Hole to run the "in Car" wires into the interior.
https://farm8.staticflickr.com/7806/47411706421_1543071105_b.jpg


After a productive weekend, I now have a list of needed parts to get ordered up. Hopefully that small glimmer, is the light at the end of this tunnel...

[Silver Bullet]

He gonna make me go boost sooner than later. :D


We need a reunion soon!!!

Looking amazing Craig!

[Silver Bullet]

Very strange to see tan carpet in the trunk of a mustang


I'm actually digging it! Nice touch and give the car character.

[Maximus]

We need a reunion soon!!!

Looking amazing Craig!

Thanks!

Tug Brock is having an ALL STICK CAR event in May. They wanted me to do the announcing, but I told them that I was planning on Running there. So, I should be there either way. It would be cool to have a SBZ showing thou! :bigthumb

[Silver Bullet]

Thanks!

Tug Brock is having an ALL STICK CAR event in May. They wanted me to do the announcing, but I told them that I was planning on Running there. So, I should be there either way. It would be cool to have a SBZ showing thou! :bigthumb
Sounds like a great time to me.... I’m in...

[draggin50]

Which track?

[Walter]

Sounds like a great time to me.... I’m in...

Aw dang!!

[S281SC]

Which track and what kind of format? Dial in? Heads up?


Sent from my iPhone using Tapatalk

[Walter]

LOL at dial in

[S281SC]

Index then maybe? Which is a fixed dial for everybody. Anyway curious about the event and venue. I would like to hear more.

I run dial in races nearly every weekend. They are Not that bad. You just have to be fast on the tree and be consistent. Hit a consistent launch and your shift points. I also enjoy heads up racing. Each has a time and purpose. My favorite is index racing. A good mix of both disciplines.


Sent from my iPhone using Tapatalk

[Maximus]

https://farm8.staticflickr.com/7870/33561230058_7b5a12df71_b.jpg

[Silver Bullet]

Needs to be heads up small tire street car! Lol

[Maximus]

Needs to be heads up small tire street car! Lol

Nobody like a Bully. :lol:

[Walter]

Needs to be heads up small tire street car! Lol

Don't make me put a 75shot on the coupe and drive around you.

[Silver Bullet]

Nobody like a Bully. :lol:

Just wanting it to be fun!!! Lol


Sent from my iPhone using Tapatalk

[Silver Bullet]

Don't make me put a 75shot on the coupe and drive around you.

Bring it!!! :)


Sent from my iPhone using Tapatalk

[Walter]

Bring it!!! :)


Sent from my iPhone using Tapatalk

Ordered!!!!

[Maximus]

Seems like that light, down that tunnel, is getting brighter as these productive days continue!

Im waiting on my JLT CAI to arrive so that I can get this buttoned up. Alternator wire needs to be run to the battery, but then under here is done.
https://farm8.staticflickr.com/7862/46548674325_34cea22c34_b.jpg

Fuel lines and all the other sensors are hooked up and ready to go.
https://farm8.staticflickr.com/7863/47410921642_8c8ba50857_b.jpg

I had to source a different lower rad hose, but with a little trimming, it worked. Black Magic 3300cfm electric fan has been my go to for all my projects, so hopefully Ill have the same results.
https://farm8.staticflickr.com/7825/47410921612_4dfc11bf94_b.jpg

ECM mounted down and out of the way.
https://farm8.staticflickr.com/7905/46548674405_49d1bfc088_b.jpg

Fuel Regulator mounted on the pass side front timing cover.
https://farm8.staticflickr.com/7925/47410921602_31397b932e_b.jpg

Hopefully Ill have more progress pics as I have more parts coming in later on in the week.


Thanks for tuning in. :D

[Crucial]

wiring job is on point. looks great Craig :bigthumb

[PKFIRE]

That looks like it belongs in there! Nice work!

[Maximus]

wiring job is on point. looks great Craig :bigthumb


That looks like it belongs in there! Nice work!

Thanks! Taking a little more time now, yields better results later.


Got the JLT installed and it looks better that I thought.
https://farm8.staticflickr.com/7835/33602019128_18f369c375_k.jpg

https://farm8.staticflickr.com/7834/47478661081_ed1421cc68_b.jpg


This is getting closer everyday that I have a chance to work on it. Last night I installed the JLT and installed an engine diaper over the oil pan. No big deal, however, If you ever decide to install an engine diaper, do it BEFORE you install the engine into the engine compartment! It was a freakin PITA!!


:)

[2Fast4You]

Looking fantastic, the covers conceal a lot for that fresh clean feeling/look. haha

[draggin50]

Man that looks so clean.

[redfirepearlgt]

Wow! Looks like it rolled out of the factory that way. :jawdrop:

[Maximus]

Almost done under here. I still need to run the factory harness to the headlights, turn signals, etc and then tie it into the Ford control pack, but this is a snap shot of how it will look.
https://farm8.staticflickr.com/7905/47514571051_96c7ac7095_k.jpg

Still quite a few things left to do, but its motivating to see more items crossed off.
https://farm8.staticflickr.com/7878/47461799332_d2e2df5a7d_k.jpg

Still on the fence with the tan in the trunk, but once the connections are made to the battery, its done back here.
https://farm8.staticflickr.com/7876/47461799192_a00a32a939_k.jpg


Almost time to roll it off the lift so I can kick open the doors and get everything wired up on the inside and seats & carpet installed. So close, yet still a lot to do...

[98stangv6]

Looking super clean! The attention to detail is awesome!

[Maximus]

Im hoping that everyone had a Great Easter!
Once my family stuff was done, I had some productive garage time!

I swear the Mustang Loves this lift. Everytime I think its time to come off, "one more thing" shows up on my to do list.
https://live.staticflickr.com/65535/47614505662_999798f76e_k.jpg

However, I was FINALLY able to roll it forward and get to the inside and run some wires! Now it still looks like a Spaghetti factory blew up in the interior, but these lights probably have not been on for 10 years, so Im making progress!
https://live.staticflickr.com/65535/47614505672_d715a46cfe_k.jpg

[2Fast4You]

Sweet

[redfirepearlgt]

DR....Have we got a heartbeat?

[firestang70]

Proper work as always.

[Kwik92GT]

Getting freakin' close! :bigthumb

[Frisby5.0]

Looks awesome Craig! Planning to run at the stick shift shootout also. We should work out a plan to try to get stangbangerz to pit next to each other...

[Maximus]

Thanks guys!

Im not sure about running there, Id like to, but there is still plenty left to do once it runs.

But I think all the SBZ peeps showing up to race should pit together, thats what we did in the past and it was always a good time! Go to the Race thread and throw the idea out there!

[redfirepearlgt]

Those of us still going down (last year was a thin and weird year due to the flood and so many rainy weekends) still park in the place I understand SBZ gathered at for years. Front corner of the pits along side the stage lanes for the slick cars.

[PKFIRE]

I always enjoyed your builds Craig! I wouldn’t mind seeing a crowd of us down at Edgewater.

[Maximus]

Those of us still going down (last year was a thin and weird year due to the flood and so many rainy weekends) still park in the place I understand SBZ gathered at for years. Front corner of the pits along side the stage lanes for the slick cars.

Ill be looking for everyone!


I always enjoyed your builds Craig! I wouldn’t mind seeing a crowd of us down at Edgewater.

Thanks! It would be cool to see everyone again.





Made some more progress last night!


Brake lights. I have to run the wires to the actual switch, but when I jumped them, the lights came on.
https://live.staticflickr.com/65535/47642724262_1a9bb8c617_k.jpg

Hazard lights blink. I have to replace the Turn Signal Flasher fuse as they were really slow when activated. The Hazards, worked fine thou.
https://live.staticflickr.com/65535/47642724092_f8b9ca16d8_k.jpg

Back up lights. When jumped, the Back up lights came on, so Ill run the wires to the TKO switch and I should be good to go.
https://live.staticflickr.com/65535/47642723992_11d6ebd4ed_k.jpg

Things left to do:
-Wire the Key switch to the 2 wires for the Ford Control Pack
-Wire the 6 wires off the main plug of the FCP to their respective locations
-Mount and wire the Dakota Digital main box (about 12 wires here)
-run the turn signal lights to the DD box
-Wire in the Neutral safety Switch to the FCP harness
-Wire the Back up light sensor
-Find the correct horn connection and wire
-Run wires under carpet and Duct tape them down (I like some extra protection on top of the wires)
-Mount new seat belts
-Install carpet
-Install seats
-Load in a Base tune file
-Fire it up!

It will still need to have a front end alignment, but to hear it actually run, will be Huge!


Thanks for tuning in!

-

[Maximus]

One of those weekends of work where you get a lot done, but it doesnt look like you accomplished anything.

Im 99% sure that Im finished under here. Ill know more once I fire it up.
https://live.staticflickr.com/65535/33855291398_03b08af11b_b.jpg

I was going to use Dakota Digitals adapter, but I would have lost gauges while tuning. So I decided to use the supplied sensors.
I drilled and tapped the factory water neck (1/8 npt)
https://live.staticflickr.com/65535/47679347992_c94834e1d6.jpg

and then installed the H2O temp sensor.
https://live.staticflickr.com/65535/33855291358_abbf8e2c67_b.jpg

The factory oil press sensor is a 1/4 npt, so I had to use an adapter.
https://live.staticflickr.com/65535/47679348092_b4b0526151_b.jpg

The Ford Control Pack does not require an oil pressure reading to run, so I installed the DD sensor in the factory location.
https://live.staticflickr.com/65535/47679348082_69e5f87f60_b.jpg

Once those wires were run into the interior, it was time to figure out what wires I will need to make it all work together.
https://live.staticflickr.com/65535/40765907003_e505017ef9_b.jpg

https://live.staticflickr.com/65535/40765906993_159bcd223a_b.jpg

https://live.staticflickr.com/65535/33855291388_8cd978dc13_b.jpg


Its getting close, but I still have quite a bit to do.

[draggin50]

I always did hate wiring... Im sure it will turn out nicely when you are done though.

[Frisby5.0]

Those of us still going down (last year was a thin and weird year due to the flood and so many rainy weekends) still park in the place I understand SBZ gathered at for years. Front corner of the pits along side the stage lanes for the slick cars.

I know where you’re talking about. Will look to go there!


Sent from my iPhone using Tapatalk

[Maximus]

Hooked everything up, and not a damn thing happened. So Ill be tearing into the wiring to see WTF happened. Aggravating to say the least. :mad:

[Kwik92GT]

Hooked everything up, and not a damn thing happened. So Ill be tearing into the wiring to see WTF happened. Aggravating to say the least. :mad:

I fucking hate wiring lol Stay with it man, you'll get it figured.

[Maximus]

I talked to Paul over the weekend and I decided to drag the Coupe up to his house on Saturday. He did a Kick Ass job on his Cobra/Coyote swap and I figured it would be good to have another set of eyes on my Coupe.
So I spent all day Saturday out in the Garage moving the cars, cleaning, hanging up old pics and getting the Coupe ready to travel.

All waxed up and shinning in the sun.
https://live.staticflickr.com/65535/32897019477_8156a7141b_b.jpg

Ill address the height of the Mustang once it runs and drives.
https://live.staticflickr.com/65535/32897019417_b27cf92cac_b.jpg

Old pics of the Monte from 96 & 97. Pic on the left is my first ever wheels up launch.
https://live.staticflickr.com/65535/32897019347_87ceb8cde9_b.jpg

All ready to get dirty once again. Its a never ending process.
https://live.staticflickr.com/65535/47841016871_42494eef82_b.jpg

Im hoping that Paul will find something easy and him call me telling me that Im dumb and he is smart and that the Coupe now runs. Ill have the SCT from Ken B in the car so hopefully Paul will be able to load that up as well and actually fire up the Coupe. :)

Thanks for tuning in.

[Kwik92GT]

Everything looking awesome as always! Hopefully it's something easy as you said and you'll be rowing gears here soon! :bigthumb

[redfirepearlgt]

Paul as in Paul Notch? That guy can fix anything. Worked with him for about 5 years directly and indirectly. He's not afraid to tackle anything. I think the guy could do a heart transplant if you asked him to. :bigthumb

[2Fast4You]

Good luck Craig, I bet it's something simple.

[Maximus]

Everything looking awesome as always! Hopefully it's something easy as you said and you'll be rowing gears here soon! :bigthumb

Thanks! Im hoping its something dumb. Im just at a point to where I need a break from it, but yet I still want it done. Paul mentioned something about coming down here, but I told him that I would drag it up to his place and let him do his thing in his own garage.


Paul as in Paul Notch? That guy can fix anything. Worked with him for about 5 years directly and indirectly. He's not afraid to tackle anything. I think the guy could do a heart transplant if you asked him to. :bigthumb

Thats him! His Cobra/Coyote swap is what made me do my Coyote swap, so Im sure he will find what I messed up.


Good luck Craig, I bet it's something simple.

Thanks! Im thinking it is, more like hoping it is.

[Walter]

Paul: you didn't have the ground hooked up...

Craig: LOL

[Maximus]

Paul: you didn't have the ground hooked up...

Craig: LOL

HA! That would be funny, it would suck, but still be funny.:lol:

[redfirepearlgt]

Check for continuity from the negative post of the battery to engine ground, and chassis ground. Multimeter should read less than 2 ohms. First place to start if absolutely nothing on the car lights up, cranks, or engages electrically. if infinity add grounding as needed and recheck. Then check voltage at the main bus feed point on the car to chassis ground. Proves out the primary ground and voltage bus circuits. A test light will not suffice for such troubleshooting.

[Maximus]

Check for continuity from the negative post of the battery to engine ground, and chassis ground. Multimeter should read less than 2 ohms. First place to start if absolutely nothing on the car lights up, cranks, or engages electrically. if infinity add grounding as needed and recheck. Then check voltage at the main bus feed point on the car to chassis ground. Proves out the primary ground and voltage bus circuits. A test light will not suffice for such troubleshooting.

My brake lights, headlights, turn signals and backup lighs works, its the Ford Control Pack thats being the PITA.:(

[redfirepearlgt]

That sucks. Sorry, I thought you meant everything dead. Paul will get you hooked up for sure. Wish i knew exactly where he lives. I'd love to run over and see the car. I know he isn't far from me...or at least wasn't. Just never was at his place though he's been to mine.

[Maximus]

Its ALIVE!!

https://live.staticflickr.com/31337/40923483813_a6850208ac_z.jpg (https://flic.kr/p/25mgxZ8)

https://live.staticflickr.com/31337/40923483803_1febe12121_z.jpg (https://flic.kr/p/25mgxYX)

I received the wrong tune file, so Im sure it will run a lot better when I load in the correct tune.

Huge Thank you to my dude Paul! He figured out a couple things I missed and a couple things I would not have found in the original wiring.
Its already back at my garage so that I can tidy up the wiring under the dash and get the interior back in. Hopefully, I have it ready to data-log sometime this week.

[2Fast4You]

A big Heck Yeah!

[redfirepearlgt]

https://i.imgur.com/3RgpA4H.png?1
YAY!

[draggin50]

Sounds pretty good!

[Kwik92GT]

Hells yeah! :bigthumb

[Maximus]

Last night was a long night, working in the interior of the car. I could swear I was in and out of the car 100000000 times and my back is feeling it today. Well that and the fact that I was up till 3am, probably has something to do with it.

Anywho....all that work, and this is what I have to show for it.
https://live.staticflickr.com/65535/46991941815_52913167df_k.jpg

A High Rent, Shifter boot.
https://live.staticflickr.com/65535/46992016675_811eba4521_z.jpg


What you cant see, is all the wiring, neatly tucked up and secured off the floor. Crazy how long that shit takes. I can plumb a fuel system in HALF the time it takes to cut and splice wires.

[redfirepearlgt]

Looks so good, I tried to scratch and sniff the screen for that fresh new car scent...:bigthumb:cool1:

[Walter]

Craig, I'll keep an eye out for console delete shifter trim like I got.

[Maximus]

Craig, I'll keep an eye out for console delete shifter trim like I got.

Cool! But Im sure those are like trying to find a needle in a haystack. Hell, I just overpaid for a radio delete panel as I couldnt find one for a deal. :o

[Kwik92GT]

Hey Craig, not sure if you've found the console delete shifter bezel yet but if not, you might want to give these guys a call. They have a ton of fox mustang stuff and I'm betting they have what you're looking for.

https://live.staticflickr.com/65535/47964741791_405969df6c_z.jpg (https://flic.kr/p/2g5tQEK)

[Maximus]

My computer must be whacked! I typed in that website and nothing came up. :(

[Kwik92GT]

No website, he does everything over the phone, might have to try a few times to get through even, but he has a crazy amount of fox parts around so I'm betting he'll have what you need.

[Maximus]

Got a few done on the Mustang this weekend, but also encountered a problem. Seems like the Hyd clutch set-up I had fab'd up isnt working at all. So Ill be calling Wilwood today to figure out if Im using the correct master cylinder or if the TOB wasnt installed correctly. Hopefully its something easy...

I also had the windows tinted 20%. Nothing too dark as I hate dark tinted windows and night driving.
https://live.staticflickr.com/65535/48036686553_53c5edebaa_z.jpg

https://live.staticflickr.com/65535/48036686633_706b6808b3_k.jpg


I figured I should continue with the interior install as well.

https://live.staticflickr.com/65535/48036686623_9967d281ff_k.jpg

https://live.staticflickr.com/65535/48036691058_f7ef60804f_k.jpg

https://live.staticflickr.com/65535/48036648196_176ffd1938_z.jpg

https://live.staticflickr.com/65535/48036643786_cbff66e266_k.jpg

https://live.staticflickr.com/65535/48036686703_3802b8c211_k.jpg

https://live.staticflickr.com/65535/48036643861_7a45d2917e_k.jpg

So now, Im just waiting to hear back from Wilwood and once we get that issue figured out, I can then start data logging to get Ken the correct info he needs to finish up the tune!

[Maximus]

Still fighting the Hyd clutch set-up not working, but I got some answers from Tilton. Seems like SPEC uses a certain style Diaphragm Pressure Plate, NOT like the 90% of the other PPs out there. So I need a different TOB to use on my Hyd Release Bearing.


It looks fine.
https://live.staticflickr.com/65535/48061364001_ab52c51ac2_k.jpg

But here you can see where the TOB was engaging the wrong area of the diaphragm.
https://live.staticflickr.com/65535/48061413058_e2c276a275_k.jpg

Now I just need to figure out how to remove the TOB from the HRB without fugging it up.
https://live.staticflickr.com/65535/48060889326_265af306e6_h.jpg

I borrowed a trans jack from my buddy and it makes this so much easier!
https://live.staticflickr.com/65535/48060889601_362cbfb141_k.jpg

While its on the lift, Paul, made this temporary Fuse block feed wire. He also told me to upgrade it when I get a chance, so I went with the thicker wire.
https://live.staticflickr.com/65535/48060985882_b19c331e7d_k.jpg

Here you can see the difference in the TOBs.
https://live.staticflickr.com/65535/48061427406_58bb9eb9a4_k.jpg


Hopefully I can get this finished up this weekend and get to datalogging. Im excited to see what Ken B can do with the tune!

[Walter]

Wooooooooo atta boy!

[Kwik92GT]

It'as gonna rock when you get it all sorted out! :bigthumb

[Maximus]

This is the fist time, in 2 years that the Mustang has moved under its own power. No pushing was involved!!

https://live.staticflickr.com/65535/48079124048_89592ac179_k.jpg


Heres a short video of me checking the brakes before I head out for a spin around the block.

https://live.staticflickr.com/31337/48079093106_cb9025d1f1.jpg (https://flic.kr/p/2gfzVk9)Untitled (https://flic.kr/p/2gfzVk9) by Craig Newport (https://www.flickr.com/photos/156546814@N05/), on Flickr



Things left to do.

Get tags for it.
Get some DOT tires
Front end alignment
Install rear seat belts and rear seat
Data log it so that Ken can finish the tune.
Put some miles on it so that I can go Beat its eyes out at the track!

[redfirepearlgt]

Super Dooper!

[Crucial]

build looks amazing so far .. dont rush to get it together, one and done.

these rear interior panels dont look like the rest of the build


https://live.staticflickr.com/65535/48036686703_3802b8c211_k.jpg

[Silver Bullet]

Awesome work! Always look forward to the pics!

[Maximus]

build looks amazing so far .. dont rush to get it together, one and done.

these rear interior panels dont look like the rest of the build

They are original and Im leaving em that way as painted panels end up looking like poo.

[QUOTE=Silver Bullet;820356]Awesome work! Always look forward to the pics!

Thanks! :)

[Kwik92GT]

In the words of Cleetus Mcfarland .... Hell yeah Brother :bigthumb

[draggin50]

Nice to see the video of it moving under its own power! The engines sound so good!

Im sure it wouldn't be easy finding a set of tan quarter plastics in good shape. I always hated the thoughts of the interior dye also. Best to leave them as they are.

[redfirepearlgt]

Man its nice to hear a Mustang sound like a Mustang and not an LS swap. Nice job Craig! and Paul for ironing out the electrical issues.

[Kwik92GT]

They are original and Im leaving em that way as painted panels end up looking like poo.



Thanks! :)


Nice to see the video of it moving under its own power! The engines sound so good!

Im sure it wouldn't be easy finding a set of tan quarter plastics in good shape. I always hated the thoughts of the interior dye also. Best to leave them as they are.

It is 100% about prep and using the proper products, I dyed my current dash from porno red to titanium and you'd be hard pressed to tell it isn't the factory dye.

Before:
https://live.staticflickr.com/4282/34897658844_1fafe50615_z.jpg (https://flic.kr/p/VaMCab)
https://live.staticflickr.com/4259/34929406283_df674e7d5b_z.jpg (https://flic.kr/p/VdAkyP)

After:
https://live.staticflickr.com/4237/34929403573_3cab18562e_z.jpg (https://flic.kr/p/VdAjL6)

[Maximus]

Damn! That looks great!

[Walter]

I've used SEM interior paint before, it's badass.

[mustangboy]

I've had great success with the SEM paint as well

[Kwik92GT]

Damn! That looks great!

Thanks! I used SEM paint/dye. You'll want to scrub the panels good with TSP, then go over them with a wax and grease remover, next you'll want to put the adhesion promoter on there and then the paint/dye. It's a little bit of work but the results will be great and it won't chip or peel like the crap we used back in the day. With as nice as this build is I think it'd be worth your time.

Here's a link for SEM showing their products etc. https://www.semproducts.com/manage/html/public/content/techsheets/SEM%20RAP-1%20Training%20Manual.pdf

[Maximus]

Man its nice to hear a Mustang sound like a Mustang and not an LS swap. Nice job Craig! and Paul for ironing out the electrical issues.

But it doesnt "chop" thou....LOL!! It is mild mannered, even with the Comp cams installed. Ken says he can do some tuning to make it sound like a cam'd Coyote, so we will see. :)



Thanks! I used SEM paint/dye. You'll want to scrub the panels good with TSP, then go over them with a wax and grease remover, next you'll want to put the adhesion promoter on there and then the paint/dye. It's a little bit of work but the results will be great and it won't chip or peel like the crap we used back in the day. With as nice as this build is I think it'd be worth your time.

Here's a link for SEM showing their products etc. https://www.semproducts.com/manage/html/public/content/techsheets/SEM%20RAP-1%20Training%20Manual.pdf

Ill check it out! Thanks for the link!!

[Maximus]

Playing musical cars and I had to stop and snap this pic...

https://live.staticflickr.com/65535/48097957046_29988f5f46_h.jpg


Ole Stang is looking Saucy! :cool1:

https://live.staticflickr.com/65535/48097957036_c1e665c5a6_h.jpg

[redfirepearlgt]

Yes. The VCT and DOHC setup eliminates that cammer sound even with larger cams up to a point. With separate exhaust and intake cams on VCT there is no overlap which creates so much of hte cam sound on a conventional pushrod engine or even on a 3V SOHC 4.6 with VCT. However, Ken can create overlap that takes place down low which will give you that fake cam sound. Whay you will notice (I have drien one with that "ghost cam" idle as they call it), that after the car settles to idle there will be a very short delay as VCT on both cams corrects to generate overlap for that cammer sound.

You probably already know this so I'm just yacking to hear myself yack. Don't mean to be sounding like I am trying to teach the teacher. No disrespect intended.

[Maximus]

Thanks! I used SEM paint/dye. You'll want to scrub the panels good with TSP, then go over them with a wax and grease remover, next you'll want to put the adhesion promoter on there and then the paint/dye. It's a little bit of work but the results will be great and it won't chip or peel like the crap we used back in the day. With as nice as this build is I think it'd be worth your time.

Here's a link for SEM showing their products etc. https://www.semproducts.com/manage/html/public/content/techsheets/SEM%20RAP-1%20Training%20Manual.pdf

I just spent $119 on Prep, sealer, texture, cleaner and paint.:)


Yes. The VCT and DOHC setup eliminates that cammer sound even with larger cams up to a point. With separate exhaust and intake cams on VCT there is no overlap which creates so much of hte cam sound on a conventional pushrod engine or even on a 3V SOHC 4.6 with VCT. However, Ken can create overlap that takes place down low which will give you that fake cam sound. Whay you will notice (I have drien one with that "ghost cam" idle as they call it), that after the car settles to idle there will be a very short delay as VCT on both cams corrects to generate overlap for that cammer sound.

You probably already know this so I'm just yacking to hear myself yack. Don't mean to be sounding like I am trying to teach the teacher. No disrespect intended.

I didnt know any of that, so Thank you for the tutorial.:bigthumb

[Kwik92GT]

I just spent $119 on Prep, sealer, texture, cleaner and paint.:)

Nice! I think you'll really like how it turns out, I'll be waiting for the "after" pics. :bigthumb

[redfirepearlgt]

BTW I overthought on the 3V. While it has VCT it is a single cam so overlap will be in effect on those engines. They still have variable cam timing. It dose the same thing as the adjustable cam gears on an old school push rod engine that allows you to reposition cam to crank position giving you fine positioning aside from simply jumping a timing link and hoping that wasn't too much. the DOHC's give more versatility to the same concept. GT500's never had this technology btw in spite of their cam configuration. Sorry for the mistake on the 3V theory. I ran a custom grind Comp cam in my 2005. It was a mild mild that had a light cam sound that sounded best with LT's after I switched to them. Sorry to beat on. I believe in correcting my missed speaking when I realize it. Enjoy that beauty. I hope you'll bring it up and make some passes with the group in spite of Dickhead's proven dickness. Or at least let us know when you plan to run it at KK or TH if you decide to come up.

[Maximus]

FINALLY!! I drove to the DMV to get an inspection, (which I found out I didnt need) and then went and got my tags!

Look close and you can see the officer, who just seconds before, walked behind my car and did not notice that I was rolling on slicks. I have DOTs coming in later today, but I wanted to make sure I had tags for tomorrow's Open House.
https://live.staticflickr.com/65535/48324630476_f9b27025dd_k.jpg

Its so cool to see it anywhere besides in my garage! I still need an alignment, but its kinda close. (I hope)
https://live.staticflickr.com/65535/48324754562_95fab82af2_z.jpg

I did some Data logging for Ken, so hopefully he sends me a revision tune to where I can take it above 4500.

[draggin50]

Makes all the hard work worth it once you are able to get it out and start showing it off. Looks good!

[Kwik92GT]

So awesome! Love this build! :bigthumb Hoping to be in the same boat soon on mine.

[Maximus]

Makes all the hard work worth it once you are able to get it out and start showing it off. Looks good!

Thanks! I did receive my first, "Thumbs up" yesterday so that was pretty cool. :D


So awesome! Love this build! :bigthumb Hoping to be in the same boat soon on mine.

Thanks! Yours is getting close and I cant wait to see at KK!!


I adjusted the drivers side, front steering bump steer and the car felt a ton better! I could get on it without fear of going into the ditch! I also calibrated the Speedo and did some more Data Logs for KenB.

https://live.staticflickr.com/65535/48343151952_72ebc30b52_k.jpg

https://live.staticflickr.com/31337/48343028581_f7ca6a2680_z.jpg (https://flic.kr/p/2gDUE9M)


Hopefully I can have the tune and alignment finished up this week. Ive been slacking on pulling the plastic pieces out and re-finishing them as Ive had too much fun driving it. Well, its been Hell Fire HOT out, so that limits my garage time as well. :lol:

[redfirepearlgt]

Looks great Craig, how about a rolling sound clip? Love how the dash looks stock 1984 but has an 8K tach and 160 vice 85mph Speedo.

[draggin50]

Those gauges do look nice!!!

[Maximus]

Still not a lot going on with the car, just driving it and data-logging for Ken. I drove it to work the other day and then met the wife downtown at a wine bar. It RIPS pretty good. Ken finally told me to get him some WOT DLs, so i did a few highway pulls. He told me to keep it under 6000, but man, from 4000 on, it pulls very fast! I "might have" seen 7, but I will neither confirm nor deny that.:D

I think I need to get the matching polished front rims to match the polished rears. The tires on the fronts here, are not DOT anyway, so I would then be 100% legal.
https://live.staticflickr.com/65535/48422688647_1efa8142fb_k.jpg


450 horses vs 1 Horsepower. :lol:
https://live.staticflickr.com/65535/48422688697_550830f772_z.jpg


I still have everything to re-do the plastic pieces, but its been too damn hot in the garage and Im enjoying just driving it. I think Ill save that project for the wintertime.

[98stangv6]

Almost time for Logan's 2 minute car review ?!

[NXcoupe]

Looks great Craig. Enjoy it, you've worked hard on it.

[Maximus]

Almost time for Logan's 2 minute car review ?!

Soon. :)


Looks great Craig. Enjoy it, you've worked hard on it.
Thanks!

[Maximus]

Back in the garage to upgrade my Clutch Master.
https://live.staticflickr.com/65535/48592326292_896d65cd3b_k.jpg

This packing blanket makes those pesky seat studs, disappear!
https://live.staticflickr.com/65535/48592326297_7a96c9d7e7_k.jpg

Seems like the pedal comes off the floor, about 1/4'' and the clutch releases. Not a big deal until Im at 7200+ and I cant shift. So I talked with Tilton and he wants me to go to a 7/8 Master.
https://live.staticflickr.com/65535/48592185221_e420993faa_k.jpg

Cam, at Cambo Built, designed this assembly using the Wilwood, reverse pedal. I like having the Hyd set-up, but if this new Master, doesnt do the trick, Ill be swapping my Cable set-up back in.
https://live.staticflickr.com/65535/48592326262_fab915339b_k.jpg


I still need to address the plastic pieces and get the interior finished up...but its been to freakin HOT!

[Silver Bullet]

Nice!! Can’t wait to see how you like the upgrade.

[redfirepearlgt]

I like the elephant pattern on the back drop. lol

[NXcoupe]

How do yoh fill the master cylinder? Is it a pain?

[Maximus]

Nice!! Can’t wait to see how you like the upgrade.

So far, the pedal is A LOT better. I just have to get it back on the ground and try it out.


I like the elephant pattern on the back drop. lol

I have all kinds of "Shop Rags" that the wife has given me over the years. Bed sheets make for great dust covers and ole T-shirts make for great rags.


How do yoh fill the master cylinder? Is it a pain?

Its definitely a 2 person job. The reservoir mounts where the cable comes through the FW and uses the old screw that holds the CLucth cable adjuster piece. When I have to bleed it, I have to un-screw the fastener and hold the reservoir as high as I can get it. Once its all done, I can put back on the FW.


I figured I better come up with a "pedal stop" before I re-install my assembly.


So I did some measuring of how far the pedal swings back.
https://live.staticflickr.com/65535/48623412913_7b0928227d_k.jpg

Went to Lowes and got some 1-1/2 x 3/16 steel and made a pilot hole.
https://live.staticflickr.com/65535/48623412903_2fbc4ea34a_k.jpg

Made it a tad longer so that I could fine tune it.
https://live.staticflickr.com/65535/48623412928_02521d2628_k.jpg

Fugged up and took off too much. Re measured and decided I could just flip what I have.
https://live.staticflickr.com/65535/48623412933_44ef3013aa_k.jpg

Cleaned it up with some acetone
https://live.staticflickr.com/65535/48623913592_26c34fdb4d_k.jpg

and threw on some paint
https://live.staticflickr.com/65535/48623766771_6a55eb6f10_k.jpg

Installed a rivet and checked the distance on more time.
https://live.staticflickr.com/65535/48623916592_d8fd391741_k.jpg

Then snapped it off and VIOLA!! A custom Pedal Stop on my custom pedal assembly.
https://live.staticflickr.com/65535/48623416178_55616b7554_k.jpg


I had my neighbor help me bleed the new Master and when I finally got it done, the pedal felt so much better! Im excited for some dry roads so that I can get the Mustang out and about to make sure its working correctly.

Thanks for tuning in.

[2Fast4You]

That's awesome Craig, good on you...

[NXcoupe]

Congrats. Sounds like it was all worth it.

[Maximus]

That's awesome Craig, good on you...

Thanks!


Congrats. Sounds like it was all worth it.

Hopefully so!

I did manage to get to work on it some more last night.

https://live.staticflickr.com/65535/48630090047_2f822637ae_k.jpg

Not a fan of a reservoir, holding brake fluid, hanging over nice new paint, but I gotta do this to get all the air out of the system.

https://live.staticflickr.com/65535/48630090062_1778d30d07_k.jpg

I did get the dash and everything in the interior buttoned up
https://live.staticflickr.com/65535/48629630313_be713e57dd_k.jpg

But, Im missing one bolt for the rear seat belt assembly, so Ill pick one up at Fastenal later today and hopefully have it installed this evening. Thats why I left the drivers seat out. (no, I didnt restore the plastic panels yet)

https://live.staticflickr.com/65535/48629992926_d85f58b004_k.jpg


Hopefully Im banging gears tonight!!

[draggin50]

So clean looking!

[JIMS SVT]

I like the polished wheel look on it

[Walter]

Nice mahi mahi !!

[Maximus]

So clean looking!

Thanks!


I like the polished wheel look on it

They were the cheapest option for my DOTs. I was debating on getting the front runners to match, but I ran out of $$$$


Nice mahi mahi !!

Best Fathers Day ever! 2017 I took my Father and Brother in law out from St Johns, VI and it was an amazing day trip! My Father in law caught one around the same size and his is mounted over his fireplace.


So I finished up the Mustang last night and got the rear seat (kinda) mounted. The Back part is just sitting there and not actually mounted. Under some hard braking, it fell forward. So Ill have to address that when I get home.
https://live.staticflickr.com/65535/48635762448_e7ce74d0db_k.jpg

My shop cat, Recee enjoys the passenger seat after she walked all over in the interior checking it out.

https://live.staticflickr.com/65535/48636264167_05b69b2710_k.jpg

Finally! I got to actually Bang some gears on the way into work today! The clutch pedal feels so much better and engages about half way into the stroke, so much freakin better!!

https://live.staticflickr.com/65535/48636120401_208edeaee6_k.jpg



Logan, Clap'd out fame, told me we are doing his 2 minute Car review, so be looking for that later today. Should be interesting...

[Walter]

Niiiiiiiice!!!!

[k062693w]

Looks Awesome Craig !!!

[Kwik92GT]

Logan, Clap'd out fame, told me we are doing his 2 minute Car review, so be looking for that later today. Should be interesting...

Sweet, I'll be looking for that one!

[NXcoupe]

Good to hear

[Maximus]

Niiiiiiiice!!!!


Looks Awesome Craig !!!

Thanks guys!


Sweet, I'll be looking for that one!

Shit, he postponed it till tomorrow.


Good to hear

TOTALLY different car now! Before, with the pedal releasing 1/4" off the floor, I couldnt shift this over 4500. Now, HOLY SHEET!! 7600!! Too much fun!!


Ole girl shines up pretty good.

https://live.staticflickr.com/65535/48637823362_bfd0b43c32_k.jpg



Im going to find a way to get the polished front runners to match. After seeing it out and about with mis-matched rims, my OCD is in overload.

https://live.staticflickr.com/65535/48637679901_b395e02169_k.jpg


Whens the next UMTR race??? :cool1:

[Walter]

7600? Go 8k!!!!!

[Maximus]

7600? Go 8k!!!!!

HA! I still dont know if KenB has it tuned for those RPMs! :confused:

I should borrow your P1 set up and go run 8s. :lol:

[Walter]

Yes!!!

[draggin50]

I like the polished look on it too.

[Evil_Capri]

:bigthumb

[Frisby5.0]

Looks great!


Sent from my iPhone using Tapatalk

[redfirepearlgt]

lookin sweet and even a little "naughty innocent" like it needs its cherry popped by making a pass or two. A song from Night Ranger is running through my head...LOL!

[Maximus]

Getting the Mustang ready to go to Clay City on Saturday to run with the UMTR. I figured I might as well do some T&Tn and have a chance to actually race at the same time.

Hes down to go racing!
https://live.staticflickr.com/65535/48757043248_cddea331ef_z.jpg

Finally getting around to adjusting the Strange Struts & Shocks...
https://live.staticflickr.com/65535/48757364821_84a049bd17_z.jpg

but I aint qualified! LoL! I guess I better take a wrench with me.
https://live.staticflickr.com/65535/48757364741_505a9b52a1_z.jpg

Ken B sent me a new tune to try out.
https://live.staticflickr.com/65535/48757364876_ea3284f353_z.jpg

So I loaded it up and went and did some data logging. This tune feels stronger, but has some idling issues when its cold, but once its warmed up, its all good.
https://live.staticflickr.com/65535/48757043613_b54883c104_z.jpg


Im looking forward to getting back to the track and seeing what the Mustang will do. It feels really good on the street, (although 1st and 2nd are kind useless with street tires) when I push 3rd and pull 4th. It comes on real strong from 4000, all the way to 7800!

Anywho, thanks for tuning in!

[cstreu1026]

Are you coming to Bowling Green with it?

[Maximus]

I wish. But I will be in South Dakota on a Family trip.

[cstreu1026]

I wish. But I will be in South Dakota on a Family trip.

It’s going to be Africa hot so you might not be missing much. Latest forecast shows 93 for Saturday afternoon.

[Maximus]

Finally! I got the bugs worked out of the Mustang and I was able to get to the track! UMTR was racing at Clay City on Saturday, and I figured that would be a decently prep'd track, so I loaded up and made the 1-1/2 trip over.

https://live.staticflickr.com/65535/48777968342_d972a6d6d2_k.jpg

KENTUCKY Dragway (Clay City) is actually a nice facility. The return road needs some Love, but everything else is nice. Plenty of Pit parking.

https://live.staticflickr.com/65535/48777968332_f1beee9c5d_k.jpg

Ive been 160 here in the Nova, and there is plenty of shut down.

https://live.staticflickr.com/65535/48777968887_8b9cfe2d9d_k.jpg

Even Racing Jesus approves!

https://live.staticflickr.com/65535/48777422388_3532394597_k.jpg

Best pass of the day, was my 1st pass. I only got 3 runs, but it was well worth the $40. Normal T&T is Fridays, at $20 and they Radial Prep!

https://live.staticflickr.com/65535/48781327618_8864fd4440_k.jpg

1st Round, I got paired with this Gorgeous 67!

https://live.staticflickr.com/65535/48777781126_41328e504b_k.jpg

https://live.staticflickr.com/65535/48777968202_198585d8f9_k.jpg

3" X-pipe with Magnflows sounds pretty sweet.

https://live.staticflickr.com/31337/48777962917_038323546f_z.jpg (https://flic.kr/p/2hjkNYD)Untitled (https://flic.kr/p/2hjkNYD) by Craig Newport (https://www.flickr.com/photos/156546814@N05/), on Flickr

Now I just need to install a 2 step and get my 60' down and I, hopefully, will have a 10 sec, NA Mustang!

https://live.staticflickr.com/31337/48777419163_2a52dc5202_z.jpg (https://flic.kr/p/2hji2kz)Untitled (https://flic.kr/p/2hji2kz) by Craig Newport (https://www.flickr.com/photos/156546814@N05/), on Flickr



As always, Thanks for tuning in!

[Kwik92GT]

That's fuggin awesome Craig! She'll be in the 10s for sure here soon, question will be, how far? :rockon:

[Maximus]

That's fuggin awesome Craig! She'll be in the 10s for sure here soon, question will be, how far? :rockon:

Im thinking 10.90s, 10.8's on a great day & prep'd track?? I dunno, but Im looking forward to finding out! :cool1:



So after my outing last Saturday, I decided that the Coupe HAS TO HAVE A 2 STEP. So I made the call to ATECH and ordered one up.

https://live.staticflickr.com/65535/48793041321_090ac0a745_k.jpg

Its pretty much a "plug n play" kinda deal. You un-plug the coil packs, plug the MSD into them, then the original harness into the MSD harness.

https://live.staticflickr.com/65535/48792675983_2eac4ac6be_k.jpg

https://live.staticflickr.com/65535/48793041331_253881b8cc_k.jpg

All finished up under the hood, you cant tell anything was changed.

https://live.staticflickr.com/65535/48792675998_5efa1586a3_k.jpg

Ill just get some 3M 2 sided tape and secure the module here in the glove box.

https://live.staticflickr.com/65535/48793182687_a551553589_k.jpg


I want to use the button on the shifter handle to activate the 2 step, so I had to come up with a switch to activate the Line Lock. The Lever for the AC/DEFROST/HEAT still functions and it depresses the switch.
https://live.staticflickr.com/65535/48792675658_a20151c461_k.jpg

I figured this lil micro-switch would do the trick! I was just hoping it would still work after 30+ years.
https://live.staticflickr.com/65535/48793041246_fc63faab4a_k.jpg

Key on, Lever up, Nothing. Key OFF, Lever Down, Nothing.
https://live.staticflickr.com/65535/48793182712_88779d2385_k.jpg

Key ON, Lever down, VIOLA!! We have Line Lock engagement! Key off, Lever down, Nothing!
https://live.staticflickr.com/65535/48793182937_683704e888_k.jpg

I didnt have a chance to use the 2 step last night as it was late when I finished up. However, this AM, it Worked!! I set it to 3000 and slowly brought the RPMS up. It hit 3000 and stayed there until I released the button!
Now hopefully I can get the Struts/Shock settings figured out and Blast me a 10 second, NA run!!

Ill be out of town next week, but the following week, Id like to head back to Clay City as their T&T is $20 and they PREP the track! If I get it squared away, Ill be coming up to race with the UMTR on Oct 19th! Yeah Im NO fan of Dick Weinle at all, but my Love for Stick Shift racing overrides my lack of liking him. :lol:

See yall soon.

[Walter]

Badass Craig!!! I just installed the same MSD unit.

[Maximus]

Badass Craig!!! I just installed the same MSD unit.

I was worried for a bit, as reading online, there were a lot of people having issues with it.

Ill know more when Im out in the Cul de Sac banging it 6500 off the 2 step!! Lol!!

[Kwik92GT]

I'm thinking .60s-.70s in the good air and dialed in a bit more. :bigthumb

[Maximus]

I'm thinking .60s-.70s in the good air and dialed in a bit more. :bigthumb

Sheeeet...If it goes a 10.99999999 with a 9, I can say, I have a 10 second Mustang. Lol!!!

[Walter]

I'm thinking .60s-.70s in the good air and dialed in a bit more. :bigthumb

I agree!!!

[Rick93coupe]

I love your idea for the line lock, that's badass! The car sounds great, I've got some coyote envy going on.

[draggin50]

Its hard to beat how they sound.

[Maximus]

Well, the 2 step is installed and Im headed to the track, today after work to try it out. I also want to practice my reaction time and rpm settings to get it all dialed in for UMTR next Saturday!

https://live.staticflickr.com/65535/48869737428_d6c43afe19_k.jpg

Ohio Valley is only 1/8 mile, so hopefully I can get some low 7.00s - High 6.99s, or just get my 60' and reaction times where they need to be, and Ill be happy!

[Maximus]

Good night at the track last night. I got 3 runs in before the fog/dew rolled in. I was hoping for 7.00-6.99 and nailed 3 6.8s!

Dusted off the old racing jacket and wiped off the helmet.
https://live.staticflickr.com/65535/48874721263_dc338a5dd6_k.jpg

Started with the 2 step at 5500, then 4800 and the last run was at 4500.
https://live.staticflickr.com/65535/48874721308_4d98dcd8d9_k.jpg

Sucks that it didnt record my last 60' as I was hoping for a 1.4x 60'
https://live.staticflickr.com/65535/48874721278_ce44a3c427_k.jpg

Grainy video.
https://live.staticflickr.com/31337/48875456247_b35399cb8e_b.jpg (https://flic.kr/p/2hsXum8)Untitled (https://flic.kr/p/2hsXum8) by Craig Newport (https://www.flickr.com/photos/156546814@N05/), on Flickr

[Kwik92GT]

https://live.staticflickr.com/65535/48871472272_e254409068_z.jpg (https://flic.kr/p/2hsB53U)

Nice hits! Now get that thing to a 1/4 mile track!

[Maximus]

Nice hits! Now get that thing to a 1/4 mile track!

Right!

Here is the last run of the night. Notice the crazy fog at the end of the track.

https://live.staticflickr.com/31337/48876227648_edeebef4c9_c.jpg (https://flic.kr/p/2ht2rE9)Untitled (https://flic.kr/p/2ht2rE9) by Craig Newport (https://www.flickr.com/photos/156546814@N05/), on Flickr

[Kwik92GT]

Damn, she's leavin' pretty good! That fog is crazy tho lol

[Maximus]

Woot Woot!! I got my 10 second ET!!

I made the trip up North to race with the UMTR this past Saturday. First past off the trailer, 10.77@126, Bam! Nice solid 10 sec ET! So everything else after that was a bonus for me. I went 4 rounds and raced another Mustang in the Finals! Holy Shit, Im in the Money!! Ole dude chopped the tree down on me an sent me packing to the RUnner up spot. However, I broke out like a stud and went a PB of 10.73@126! Heck, I even came home with $170! So I had a Great night!

Its offical, Im back in the UMTR!
https://live.staticflickr.com/65535/48935061968_8b06525d74_k.jpg

Saw Dave and Jeff there along with some other old friends. I was happy to be back racing and seeing everyone. Im looking forward to racing next year with them all.
https://live.staticflickr.com/65535/48935796232_af5be1b46d_k.jpg

Ran so fast, I lost my passenger side, front windshield molding and bent the top one!
https://live.staticflickr.com/65535/48935796092_f301a0060d_k.jpg

Ill just race without it.
https://live.staticflickr.com/65535/48935796107_d41d4c6e4e_k.jpg

The calm before the ONE time trial.
https://live.staticflickr.com/65535/48935796292_c334e1bae5_k.jpg

Fuzzy Penguins keeping the Dew off the windows.
https://live.staticflickr.com/65535/48935608686_04421fb8de_k.jpg

Personal Best, 10.73@126
https://live.staticflickr.com/65535/48935796027_c8113ab053_k.jpg


It just now realized that IF I would have hit the brakes, I wouldve won. LOL!!!

[gzbs197]

Nice job!!!!

[Maximus]

Thanks Dave for the "Action" shots!

https://live.staticflickr.com/65535/48936426036_d3226d0b45_k.jpg

https://live.staticflickr.com/65535/48935878713_66a2cc8670_k.jpg

[draggin50]

Looks good!

[Walter]

Looking good!!!

[Kwik92GT]

That's some good shit right there! Diggin' the old school "bangerz shirt. :cool1: You should have Dave make you a poster for the garage of that first action shot!

[Maximus]

Thanks guys!

Yup, I dug the ole Skull & SBZ shirt out and decided to take my buddy Vinny along for the ride. :)

I opted for the lower res download so that I could make an 8x10.

https://live.staticflickr.com/65535/48941641586_e535606ef2_k.jpg

Now if the wheels wouldve been up, it would have been a different story! LoL!

[NXcoupe]

Car looks great. I can't wait to get back out with something fast.

[firestang70]

Car looks and runs great.

[Maximus]

I'm thinking .60s-.70s in the good air and dialed in a bit more. :bigthumb

BAM!
https://live.staticflickr.com/65535/49013050597_f6495d511e_k.jpg

Even more BAM!!
https://live.staticflickr.com/65535/49013050592_4f4262f641_k.jpg


Im hoping the weather holds up for our Track Day at Clay City on the 17th. There is 50 of us attending and they WILL be prep'n the track. So hopefully I can knock off some more ET. :cool1:

[Maximus]

I had a Great time at the Track yesterday, made some hits, but I couldnt get the car off the line. I did get to see Walt and Shannon run some Personal Bests, so that was cool and worth the trip.:D

https://live.staticflickr.com/65535/49084155563_0b6446dfdf_k.jpg

https://live.staticflickr.com/31337/49084154468_da8221828d_b.jpg (https://flic.kr/p/2hMp84j)Untitled (https://flic.kr/p/2hMp84j) by Craig Newport (https://www.flickr.com/photos/156546814@N05/), on Flickr

https://live.staticflickr.com/31337/49084667661_f9fd9edc55_c.jpg (https://flic.kr/p/2hMrKBt)Untitled (https://flic.kr/p/2hMrKBt) by Craig Newport (https://www.flickr.com/photos/156546814@N05/), on Flickr

I tried to end the year on a high note, but couldnt get it done on this day.
When I built this car, I was hoping for an ET faster than a 11.0. So when I ripped off that 10.59, I was THRILLED!!. I know there is more in it, I just have to get with my chassis guy and see what we can do and get my 60" down.
Oh well, the tracks are closed, and the Stang is now in Storage for the Winter. However, Im looking forward to a SBZ Track day in the Spring, so hopefully the Mods in here can make that happen. :cool1:

[Kwik92GT]

Mission accomplished Craig! Your car rips man and it's awesome to see you on The Dozen again. Throw some boost on 'er over the winter! :smokin:

[Maximus]

Mission accomplished Craig! Your car rips man and it's awesome to see you on The Dozen again. Throw some boost on 'er over the winter! :smokin:

LoL!! Thanks man! Its the Nova's turn for upgrades, so probably no boost this year.

[draggin50]

High 1.30 60 ft. and some 10.30's maybe?

[Maximus]

High 1.30 60 ft. and some 10.30's maybe?

Dude, I would LOVE any 60' below a 1.49!

[draggin50]

I couldn't get my Cobra to 60 worth a crap. I think the best it went was a 1.46.

Bought the black car from Shannon and my first pass was a 1.38 I think. He has these cars down. Whole different world once they hook and move without blowing the tires off.

[Maximus]

I couldn't get my Cobra to 60 worth a crap. I think the best it went was a 1.46.

Bought the black car from Shannon and my first pass was a 1.38 I think. He has these cars down. Whole different world once they hook and move without blowing the tires off.

I shouldve let him rub some of that Vodoo Shannon Magic on mine! LoL!:lol:

[Walter]

He's the 60ft whisperer LOL. You need more gear Craig, 456 or 471. It will change that car....

[Walter]

Put that thing on e85 too.

[Maximus]

He's the 60ft whisperer LOL. You need more gear Craig, 456 or 471. It will change that car....

Wouldnt that hit the tire harder than my 4.30 gear thats in there now?

[Walter]

Yup, need a better tire too.

[draggin50]

What tire are you on now?

[Maximus]

What tire are you on now?

26x8.5-15 Slick with a Tube.

[draggin50]

Your rear end narrowed?

I have a few different wheels and tires Id let you try but they are the 6.5 backspacing. I never had any luck on the 26x8.5 with the stick. The best I had was the 26x10 stiff wall mickey and now the 27x10 M&H's.

[Maximus]

My 8.8 is cut down 2.5" on each side, but THANKS for the offer!

[draggin50]

4 inch backspacing? Love the way they look with less backspacing.

[Maximus]

Im kinda over the whole exhaust hanging down, so close to the ground. So I found these...


CG's SS, Shorty haders!
https://live.staticflickr.com/65535/49214217936_aece11b521_k.jpg

https://live.staticflickr.com/65535/49214217931_c2b2319dce_k.jpg

I talked to my Fab guy and he said that he could "definitely" get me some more ground clearance and possibly find some more HP & TQ!
I mentioned that I like have cold drinks at the track, but I didnt want to lugg around a cooler. So he came up with this...

https://live.staticflickr.com/65535/49214449922_0b91890054_k.jpg

Freakin Sweet! I will now be able to race at the track, knowing my cans of beverage are safe, Iced and secure in my trunk!! Too COOL!!!


:D

[Walter]

Be able to dry your hair soon too!!!

[draggin50]

Very nice pieces!!!

That will surely pick up a few ponies!

[Silver Bullet]

Those are awesome for Beer! Trust Me! lol:cheers:

[Kwik92GT]

You sure that's for holding beverages? I mean, it just really closely resembles a water/ice tank for an intercooler. :dunno: lol

[Walter]

You sure that's for holding beverages? I mean, it just really closely resembles a water/ice tank for an intercooler. :dunno: lol

Double duty bro. Beers in the IC tank, burritos on the engine. Make a hit and party time!

[redfirepearlgt]

I thought at was a wet well for when you go fishing at KY Lake.

[2Fast4You]

I like it no matter what direction you decide to use it for, Cold beverages are nice though.

Sent from my Z965 using Tapatalk

[draggin50]

Still gonna keep the stick shift?

[Maximus]

Fishing well......BWAHHAHA!!!! I hate for a Goldfish to get sucked up and sent through an intercooler.

I have a T56, but I screwed up and got a GM T56. So now I have to decide on what I want to do. Everything is telling me to go with a PG and Boost, but I already have that with the Nova.

I dunno, the Stang is at my Father in laws shop while I tear into the Nova, so its kinda outta site outta mind right now.

[redfirepearlgt]

I learned something new today. I just assumed a T56 would be a T56 (and so on for trans builders in general) and the bolt pattern they use would have to be adapted to by any maker choosing them.
Have you looked into seeing if a 10R80 could be adapted? That little 4-eye would be really hauling big time with a simple transbrake kit and a nice stall IMHO. Would obviously need an ECU swap. But then you get into all kinds of additional tuning as well. Where as with the PG or any other mech shifted auto its how you set it up mechanically with no additional learning curve or third party tuning involvement.

I just saw where a guy took his 18 GT (or 19 - same same) and went 10.53@ 135 N/A (E-85 and some mods). Car weighed 3500 with him in it. Did it on a 1.5x 60ft as well. 3.55 gear as well. Nothing massively short and on a stock converter with a tune generated transbrake that lets him leave at 3000RPM.

A 10R80 with boost in a fox body? WOW! That wouldl be something to see.

[Kwik92GT]

Fishing well......BWAHHAHA!!!! I hate for a Goldfish to get sucked up and sent through an intercooler.

I have a T56, but I screwed up and got a GM T56. So now I have to decide on what I want to do. Everything is telling me to go with a PG and Boost, but I already have that with the Nova.

I dunno, the Stang is at my Father in laws shop while I tear into the Nova, so its kinda outta site outta mind right now.

I was going to say a 6R80 and boost but a 10R80 would be cool as well. You could drive the thing anywhere, with decent or even really good mileage, bust some ass and drive it back home. Could be an awesome setup for something like Drag Week. :cool1:

[redfirepearlgt]

A 4R70 setup might be another option. They make setups for the Coyote. Just not sure if there is a kit for a Coyote in a Fox. Of course anything can be made to fit when one has Craigs talent and skill level.

http://www.jpcracing.com/jpc-4r70w-swap-package-s197/

The link is for a 2005-2014 kit, but they may have an unlisted option for your fox application.

[Maximus]

Dang. Yall like spending my $$$$!! LoL!!

10R80, those even fit in a Fox?

[redfirepearlgt]

^^^ You got money you ain't even spent yet! I'm just a poor factory worker living through your build project.

[redfirepearlgt]

Dang. Yall like spending my $$$$!! LoL!!

10R80, those even fit in a Fox?

Just found this Craig....

https://www.svtperformance.com/threads/10r80-in-fox.1181156/

According to the thread Power by the Hour in FLA has been involved in doing 6R80 and 10R80 swaps in Fox Bodys. I looked at the site and saw nothing specific but that doesn't mean they don't.

[draggin50]

The 10 speed would be bad ass!

[NXcoupe]

My fox has a 6r80 using a stifflers crossmember. Fit like a glove. the 10 spd isn't much larger

[2Fast4You]

Dang. Yall like spending my $$$$!! LoL!!

10R80, those even fit in a Fox?

Someone has to spend it. Haha

[Kwik92GT]

Dang. Yall like spending my $$$$!! LoL!!

:yup: :yup:

https://media.giphy.com/media/JpG2A9P3dPHXaTYrwu/source.gif

[redfirepearlgt]

^^^ Man Craig sure looks younger without all the stress of running a business.

[Maximus]

Finally!! I went and picked up my Mustang from my Father in Laws shop. I was storing it over there while I was tearing into the Nova.

All snuggled up under the cover.
https://live.staticflickr.com/65535/49640048508_174069f1ac_b.jpg

On the trailer headed home!
https://live.staticflickr.com/65535/49640840282_c1dfe424f4_k.jpg

https://live.staticflickr.com/65535/49640565851_12709fe8bd_k.jpg

Yesterday, I took my girls out to the Dollar Store.
I suggested we take the Mustang.

https://live.staticflickr.com/31337/49640792002_a10e5672b6_n.jpg (https://flic.kr/p/2iCA31b)


I guess I shouldve washed it, but I got busy. A dirty Mustang or clean one, is still a fun drive to work.
https://live.staticflickr.com/65535/49639993978_79c47c1b6c_k.jpg

[draggin50]

That's a nice shop!!

[Walter]

Looking good Craig!!

[Maximus]

That's a nice shop!!

It is. The building was only 3 years old when he bought it. Since then, he has done all kinds of cool stuff to it. The Camaro in the background, he has been doing all the work to it himself. (Detroit Speed suspension & mini-tub) So he does get the shop dirty.


Looking good Craig!!

Thanks! Terry posted up pics of you two out and about, so i decided that I too, want to be out and about in my Mustang. :D

[Walter]

You got some killer rides my friend!!!

[redfirepearlgt]

sooper dooper pooper scooper! Looks great!

[Maximus]

You got some killer rides my friend!!!

You and Shannon set the bar pretty high.:coo1:


sooper dooper pooper scooper! Looks great!
Uhhh, what?? :lol:

[redfirepearlgt]

Uhhh, what?? :lol:[/QUOTE]

I guy I used to work with would say that when he liked an idea you had, was agreeing with you, or was aknowledging he heard you and would comply. It stuck with me over the years.

Love to see your work. I wish I was 30 years younger so I could go into debt, build a garage, fill it with tools and a lift and enjoy this hobby beyond basic tune-up and bolt ons work, understanding the theory, and driving the car. So I am building a theater room in my basement instead. I at least have the tools for that and the structure already exists.

Hope to see you this spring...and the car!

[Maximus]

I decided to change out the rear coil over springs over the weekend. I removed the 150s, installed some 95s, and those bottomed out. So I ended up running some 125s
https://live.staticflickr.com/65535/49716650787_79bc10b877_k.jpg

Looks a lot better now.
https://live.staticflickr.com/65535/49716336391_a50fa56ba6_k.jpg

After a few test hits in Mexico, I hit up the local car wash.
https://live.staticflickr.com/65535/49716651542_1453ea14df_k.jpg

I dont know about you guys, but I cant wait to hit the track again! All this quarantine shit sucks ass!

[draggin50]

You running the coil overs in the stock location? What length did you go with?

I always had issues with the ones I had. Either it was to hard, to soft and bounced something horrible, or just sat to low. I ended up going back to a regular spring rather than fighting it at the time.

Im with you! I cant wait till this all clears up and we can get back to living a normal life again. I had the black car out for 10 minutes the other day on back roads just to get over the fever some!

[Maximus]

You running the coil overs in the stock location? What length did you go with?

I always had issues with the ones I had. Either it was to hard, to soft and bounced something horrible, or just sat to low. I ended up going back to a regular spring rather than fighting it at the time.

Im with you! I cant wait till this all clears up and we can get back to living a normal life again. I had the black car out for 10 minutes the other day on back roads just to get over the fever some!


Yes, I ended up running the 12" x 125lb Afco Coil over springs. The car seemed to like the switch, but until the track opens, kinda hard to tell.

[mustangboy]

What shocks are yoy running? Maybe you need something with more adjustability or better dampening

[Maximus]

What shocks are yoy running? Maybe you need something with more adjustability or better dampening

Strange Double adjustable, front and rear

[Walter]

Strange Double adjustable, front and rear

High rent!!!

[draggin50]

Good parts for sure!

Once you get it sorted out, you shouldn't have any issue getting it to 60 like it should. Should pick up a good bit too Id think.

[Maximus]

High rent!!!

Wait, how many single digit Mustangs do you have? :lol:


Good parts for sure!

Once you get it sorted out, you shouldn't have any issue getting it to 60 like it should. Should pick up a good bit too Id think.

Man Im hoping so! I was watching Jacob Lamb leave at 7400 with the front wheels in the air. :cool1:

[draggin50]

Im sure you can get you 60ft. down in the low 1.30's and pick up a couple/few tenths in the quarter.

I love how the coyote cars leave and how they sound. Very hard to beat them!

[Walter]

Wait, how many single digit Mustangs do you have? :lol:



Man Im hoping so! I was watching Jacob Lamb leave at 7400 with the front wheels in the air. :cool1:

You can leave like that too with 300 lbs in the trunk like they have!

[Maximus]

You can leave like that too with 300 lbs in the trunk like they have!

If it would pick me up I would. Hopefully my new coil springs will help.


Take your "kid" to work day!

https://live.staticflickr.com/65535/49730721766_eef1291c30_k.jpg

https://live.staticflickr.com/65535/49730721786_e116bd6159_k.jpg

I can not WAIT to get back to the track on slicks!

[draggin50]

Looking good! Beat it hooks good on those tires on the street!

I am a fan of the polished rear wheels!

[Maximus]

Looking good! Beat it hooks good on those tires on the street!
I am a fan of the polished rear wheels!


Nope. :lol:

I was planning on purchasing the matching fronts, but Im waiting till after the Nova is running and this Virus BS is over with.

[draggin50]

I think that will be a night and day difference!

Im in the same boat with this virus crap. I had plans to get most of my stuff bought and this hit. Im almost nervous now to spend a good amount of cash with not knowing how this is going to play out or how long. Im still working but as soon as a few people start getting it, Im sure they will shut us down.

[k062693w]

Absolutely Sexy Craig ...

[Maximus]

I think that will be a night and day difference!

Im in the same boat with this virus crap. I had plans to get most of my stuff bought and this hit. Im almost nervous now to spend a good amount of cash with not knowing how this is going to play out or how long. Im still working but as soon as a few people start getting it, Im sure they will shut us down.

We are still working, but Im not sure how long the people Not working will be spending money on Racecar parts. Since I rely on them, Im not pushing my luck. It dont think it looks too hateful with mis-mathced rims.


Absolutely Sexy Craig ...

Thanks Aaron!


Finally got around to cleaning and organizing my garage.

Before
https://live.staticflickr.com/65535/49773976792_64ac2369cc_k.jpg

After
https://live.staticflickr.com/65535/49773976752_4e2963e072_k.jpg

This shit, takes FOREVER!! I worked for 3 hours and I still had tools not organized.
https://live.staticflickr.com/65535/49775027927_935e2cc176_k.jpg

All tucked in
https://live.staticflickr.com/65535/49773117163_d1c091744f_k.jpg

My SBZ hoodie laying on the Nova.
https://live.staticflickr.com/65535/49774697051_e603fd5595_k.jpg


Man, this Lock down shit sucks!! At least I was able to get out to Mexico last weekend!

Kinda hard holding a phone, steering and trying to shift. LoL!!
https://live.staticflickr.com/31337/49775069067_cc2fb7984f_b.jpg (https://flic.kr/p/2iQseTZ)


https://live.staticflickr.com/31337/49774208733_601cfa2083_b.jpg (https://flic.kr/p/2iQnQ9D)



Im hoping everyone is staying safe in this BS Lock down!!

[Kwik92GT]

Lookin' good as always Craig! You got an ET goal for the Nova this year? Something like you did a good while back where you drove to the track, ran 8s, and then drove it home, only this time it'll be 7s? :cool1:

[2Fast4You]

Looking good Craig

Sent from my SM-G975U1 using Tapatalk

[draggin50]

No it still looks real good with those wheels! Id be perfectly content with it that way.

[Maximus]

Looking good Craig
Thanks!

Lookin' good as always Craig! You got an ET goal for the Nova this year? Something like you did a good while back where you drove to the track, ran 8s, and then drove it home, only this time it'll be 7s? :cool1:
Thanks! At this point, Id be happy with it running again.

No it still looks real good with those wheels! Id be perfectly content with it that way.
I dunno, If I get my STIMULUS Check, its on!! LoL!!

[draggin50]

Stimulus=Car parts!!!

[Maximus]

I think Im going to swap these out when I get home.

https://live.staticflickr.com/65535/49805887197_d8e989a2ba_k.jpg

https://live.staticflickr.com/65535/49805887202_83efe390ab_k.jpg

[Walter]

Red and gold is a good look!!!

[Maximus]

I was planning on T&T'n tomorrow, but KY Dragway called it due to weather. I still plan on changing the oil and bleeding the brakes as I have always had a Hard pedal.

Swapped the Nova and Mustang
https://live.staticflickr.com/65535/49814046848_28902799af_k.jpg

https://live.staticflickr.com/65535/49814895077_3c9de4a266_k.jpg

https://live.staticflickr.com/65535/49814895067_f082ff7199_k.jpg

One or Both of my daughters dont realize it yet, but they get to help me with the brakes when I get home. Ill even let them Tik Tok while they help.
I was going to install the slicks, but since I have a week to burn some 93, Ill leave the street tires on. Then its time to fill up with E, upload the new tune, hammer around town and if everything feels good, install the slicks!

Yall have a good weekend!

[Maximus]

Random pics....

I drove it to work the other day...
https://live.staticflickr.com/65535/49837983292_ef4ee722bc_k.jpg

and I got to use my DRAGY.
https://live.staticflickr.com/65535/49837733336_abee4186fb_k.jpg

Cool APP and GPS that seems like its pretty accurate.
https://dragymotorsports.com/

All cleaned up and ready to go back into the garage before the rain hits.
https://live.staticflickr.com/65535/49837682376_9b9929d22a_k.jpg

[redfirepearlgt]

That car is going to run way faster than that........sand bagger! LOL! Great pics man. Car looks awesome. Love the late model 5.0 badges. Nice subtle touch.

[draggin50]

That 60ft on the street tires sure helped!!! We all know its gonna fly!

[Maximus]

That car is going to run way faster than that........sand bagger! LOL! Great pics man. Car looks awesome. Love the late model 5.0 badges. Nice subtle touch.

Good eye! Thanks!


That 60ft on the street tires sure helped!!! We all know its gonna fly!

Im about ready to throw the slicks on, get my phone mount installed and make some Dragy videos. :D

[Maximus]

Boss is gonna be angry when my ole Fox Body goes around him. :D

https://live.staticflickr.com/65535/49842357993_50c33d5985_k.jpg

https://live.staticflickr.com/65535/49842901556_0eb8d79055_k.jpg
















when i add boost

[redfirepearlgt]

^^^ There nothing more fun than putting the gap on ANY Corvette.

[cstreu1026]

You really need a blower so he needs a telescope to see you

[Maximus]

You really need a blower so he needs a telescope to see you

After seeing the Video, Brandon put up on his FB page, no thank you. I was thinking the Twins I took off the Nova would be kinda cool. 366's FTW.:cool1:

[draggin50]

Im not a Corvette guy but that's a good looking car!!

[Walter]

After seeing the Video, Brandon put up on his FB page, no thank you. I was thinking the Twins I took off the Nova would be kinda cool. 366's FTW.:cool1:

What vid?

[S281SC]

On facebook. White coyote gt with a Whipple ripped the crank snout off and pretty much destroyed everything but the block.


Sent from my iPhone using Tapatalk

[draggin50]

Wow, didn't see that one yet but I will have to search for it. Sounds violent...

[S281SC]

https://www.facebook.com/1415709552/posts/10217990735346056/?d=n


Sent from my iPhone using Tapatalk

[redfirepearlgt]

That's not a typical failure. There is something more going on that generated that...extreme sideloading and/or wobble has been induced to cause that failure. The addition of the rotating load of a centri or PD unit isn't going to cause something like this to happen IMHO. After owning FI setups for more than 12 years now I have never seen that happen.

The setup that caused this will tell the full story. .

[Maximus]

Id love to install a Procharger on mine, but I have these 2 just sitting here.

https://live.staticflickr.com/65535/49858909043_a5a55f8acc_k.jpg

Of course that will lead to a whole bunch of upgrades and more money spent.:(

[redfirepearlgt]

^^^ Oh yeah....twin 55's. Will make nice boost and spin up fast. Can't go wrong there...especially when you have them and the tools and place to do it all yourself. Hopefully there will be a track open in the area at some point.

[Maximus]

^^^ Oh yeah....twin 55's. Will make nice boost and spin up fast. Can't go wrong there...especially when you have them and the tools and place to do it all yourself. Hopefully there will be a track open in the area at some point.

66s :D

[redfirepearlgt]

OH! Sorry. Looked like 5's on the casings.

[Walter]

66s :D

You won't do it...

[NXcoupe]

Id love to install a Procharger on mine, but I have these 2 just sitting here.

https://live.staticflickr.com/65535/49858909043_a5a55f8acc_k.jpg

Of course that will lead to a whole bunch of upgrades and more money spent.:(

They....look.....like......twins!

[Maximus]

You won't do it...

My wallet agrees with this statement.


They....look.....like......twins!

Vinny was a Bad/Good influence. :cool1:

[k062693w]

Id love to install a Procharger on mine, but I have these 2 just sitting here.

https://live.staticflickr.com/65535/49858909043_a5a55f8acc_k.jpg

Of course that will lead to a whole bunch of upgrades and more money spent.:(




:drool::drool::drool:

[Maximus]

The Joys of Stick Shift Racing! Made 2-1/2 hits on Saturday and had to be towed back to the trailer.

Im ordering a new Trans jack, as Im sure Ill be doing this more often.
https://live.staticflickr.com/65535/49909132302_cad7f1a54c_k.jpg

This, will be getting some 3" SS V-bands as I was banging on them for an hour trying to get them off the headers.
https://live.staticflickr.com/65535/49908316553_19828b16cc_k.jpg

Ethan snapped a couple decent pics of the Mustang launching
https://live.staticflickr.com/65535/49908830986_98525ce6b3_b.jpg

https://live.staticflickr.com/65535/49908830966_fc10465011_b.jpg


Hopefully, Ill have the trans out tonight and on its way to get fixed tomorrow.

[draggin50]

Those pictures are nice!

I cant wait to get to the track. This shit is getting old!

[Maximus]

Those pictures are nice!

I cant wait to get to the track. This shit is getting old!

Yes it was!

It was so nice to get to the track and see people out enjoying the outdoors! Even with a busted trans, I had a Blast and would do and will do it again!

[2Fast4You]

Great pics Craig, he snapped some almost as good as Brian would have. let us know about the trans, sounds like you may have busted the gears.

[NXcoupe]

My wallet agrees with this statement.



Vinny was a Bad/Good influence. :cool1:

Yes, don't I know.

[Maximus]

Wooo...another cool shot from Saturday. Maybe, one day, Ill have a Wheels up pic.:o

https://live.staticflickr.com/65535/49919720276_b6cf37c743_k.jpg

[Walter]

I've never done a wheelie. My stuff is slow. Ugh.

[2Fast4You]

I've never done a wheelie. My stuff is slow. Ugh.Or the suspension is set up properly, maybe...
Me neither, maybe some day though.

Sent from my SM-G975U1 using Tapatalk

[redfirepearlgt]

I've done wheelies.......on my bike.